Car Gear Picks

Ttp223 Touch Sensor Buying Guide

The TTP223 is a single-channel capacitive touch sensor IC that replaces a mechanical pushbutton with a glass, plastic, or acrylic sensing pad, offered almost exclusively as a breakout module board. The only real trade-off buyers face is output configuration and supply tolerance: fixed self-lock versus momentary versus jumper-selectable signaling, and 2.0–5.5 V operation versus 3.3 V logic compatibility. The decision rule is simple: buy a breakout with solderable pads, an exposed mode jumper, and a documented output type, and skip sealed no-name boards with no mode control.

Sensor Type:Single-channel capacitive touchOutput Mode:Momentary / toggle / jumper-selectableSupply Voltage:2.0-5.5 V DCOutput Signal:Digital high/low, few mA

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • TTP223B is the standard die: one capacitive channel, active-high or active-low output set by a board-side jumper, with three modes (momentary, toggle/self-lock, timers).
  • Supply range is 2.0–5.5 V DC, so the module runs directly from 5 V Arduino rails and 3.3 V logic, but drive capability is only a few milliamps for LED or MCU input use.
  • Sensitivity is set by the pad's effective capacitance; a 10–20 mm copper or foil pad on 1–3 mm glass or plastic is the practical range for reliable 0/1 switching.
  • Boards come in two output families: a single digital OUT for direct MCU or relay-module trigger, or parallel OUT and inverted OUT for wiring either polarity without code changes.

Best use cases

  • Best fit: hidden or sealed user interfaces on 1–3 mm acrylic, glass, or plastic (lamp touch bases, control panels, enclosures) where a mechanical button would wear or admit moisture — pick a momentary or jumper-selectable board and size the pad to 10–20 mm.
  • Best fit: Arduino, ESP32, or Raspberry Pi DIY input where 5 V or 3.3 V logic and a single digital pin are all that is needed — pick a breakout with active-high/active-low jumper and solder pads, and expect switch behavior, not analog sensing.
  • Wrong fit: direct AC mains switching — the TTP223 is a low-current logic sensor and must drive a relay module or SSR rated for the load, never the mains circuit itself.
  • Wrong fit: high-noise or wet-through environments and metal-face panels without an insulating overlay — capacitive sensing drifts and false-triggers, so choose a sealed industrial capacitive sensor instead.

Buying tips

  • Match output mode to the circuit: momentary for push-to-activate, self-lock/toggle for on/off latching, and jumper-selectable boards if you need to switch behavior without resoldering.
  • Buy the active-high or active-low variant your MCU expects, or a board with both OUT and inverted OUT pins, so you avoid an external inverter or code workarounds.
  • Check the module's stated supply range covers 2.0–5.5 V and keeps 3.3 V logic thresholds valid; boards that only list 3.3 V or only 5 V are less flexible across platforms.
  • Choose gold-plated or HASL pads and a board with clearly marked S1/S2 mode jumpers; look for breakout dimensions and pin pitch (2.54 mm) so it drops into breadboards and screw-terminal carriers.

Specs

Sensor TypeSingle-channel capacitive touch
Output ModeMomentary / toggle / jumper-selectable
Supply Voltage2.0-5.5 V DC
Output SignalDigital high/low, few mA

Related searches

What to check before buying

  • Measure your overlay: the sensing pad sits behind 1–3 mm of non-conductive material, and thicker glass or plastic reduces sensitivity, so plan a larger pad or a different sensor for thick panels.
  • Confirm the logic rail: the module must be powered from a 2.0–5.5 V source and its OUT must match your MCU's input voltage (3.3 V or 5 V) to avoid level shifting.
  • Plan the load path: the TTP223 output cannot drive lamps, motors, or AC loads, so budget a relay module, MOSFET, or SSR plus a separate load supply.
  • Check the sensing surface: metal faceplates, nearby wiring, and hand proximity cause false triggers, so mount the pad with clearance and a firm insulating overlay.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.