Car Gear Picks

Camshaft Position Sensor Buying Guide

A camshaft position sensor (CMP) reports cam phasing and rotational position to the ECU so it can sequence fuel injection and spark; a failing sensor causes hard starts, misfires, and P0340-family codes. The core trade-off is magnetic sensing architecture (Hall-effect vs inductive) and connector/harness quality, not price. Buy the exact sensor type and connector your engine management expects; anything else is a compromise.

Sensor Type:Hall-effect (3-wire) vs Inductive (2-wire)Signal Output:Digital square wave vs AC sine waveConnector:Sealed OEM keyway, 2- or 3-pinAir Gap:0.5–1.5 mm (inductive types)

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Hall-effect sensors output a digital square wave and need a 3-wire supply (reference, ground, signal); inductive sensors output an AC sine wave on 2 wires and require an air-gap spec.
  • OEM-style sensors use sealed connector housings and glass-filled polymer bodies rated for continuous oil and heat exposure above 150°C; generic bodies warp and leak.
  • Target wheel and sensor air gap is typically 0.5–1.5 mm; a sensor with the wrong tip length or mounting depth will misread or contact the reluctor.
  • Signal type must match the ECU input: swapping Hall for inductive (or vice versa) produces a no-start or P0335/P0340 even if the sensor bolts in.

Best use cases

  • Best fit: a 2010s OBD-II engine with a 3-wire Hall sensor — pick an OEM-equivalent connector and mounting depth, and replace the pigtail if the harness is cracked.
  • Best fit: a distributor-era or early EFI engine with a 2-wire inductive pickup — buy the sensor with the specified air gap and verify reluctor tooth condition before install.
  • Wrong fit: buying a universal 'fits many' sensor without confirming signal type, connector keyway, and tip length — it may bolt in but will not start the engine.
  • Wrong fit: replacing the CMP sensor for a P0340 code without checking the cam reluctor, timing chain stretch, or harness continuity — the new sensor will throw the same code.

Buying tips

  • Count the wires at the factory connector: 3 wires = Hall-effect, 2 wires = inductive; match the replacement exactly and never adapt one type to the other.
  • Measure the old sensor's tip length and mounting flange depth; a replacement more than 1 mm off changes the air gap and can cause intermittent cam sync loss.
  • Match the connector keyway and latch style to the factory harness; an unsealed or mis-keyed connector causes water intrusion and P0340 after rain or washes.
  • For VVT engines, confirm the sensor reads the cam phaser target wheel (not the crank); cross-referencing the OEM part number is faster than visual matching.

Specs

Sensor TypeHall-effect (3-wire) vs Inductive (2-wire)
Signal OutputDigital square wave vs AC sine wave
ConnectorSealed OEM keyway, 2- or 3-pin
Air Gap0.5–1.5 mm (inductive types)

Related searches

What to check before buying

  • Confirm the engine code and model year — cam sensor part numbers change across mid-cycle engine revisions even within one model line.
  • Inspect the factory connector for cracked latches, corrosion, or oil wicking; a new sensor on a damaged pigtail will fail again.
  • Verify the cam target wheel or reluctor has all teeth intact and is not loose before fitting a replacement sensor.
  • Check clearance to the timing cover, intake manifold, and firewall — some sensors require a specific socket or a short extension to install without breaking the body.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.