Car Gear Picks

Crank Position Sensor Buying Guide

A crank position sensor (CKP) is the engine management component that reports crankshaft speed and angular position to the ECU, timing ignition and injection. The primary trade-off is between inductive (passive, two-wire, signal strength falls at low RPM) and Hall-effect (active, three-wire, square-wave output stable down to zero RPM) designs, plus connector and resistance tolerances that determine drop-in fit. The decision rule: match sensor type, connector keying, and air-gap spec to your exact engine code; a generic 'fits many' sensor with wrong resistance or mounting depth is a compromise that causes no-start, misfire, or intermittent stall.

Sensor Type:Inductive (2-wire) vs Hall-effect (3-wire)Air Gap:0.5–1.5 mm typical (engine-specific)Connector:Keyed pinout varies by engine codeMounting Depth:Match block bore and O-ring size

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Inductive CKP sensors are two-wire variable-reluctance devices generating an AC sine wave; signal amplitude drops with RPM, so low-speed cranking faults often trace to excessive air gap or damaged reluctor teeth.
  • Hall-effect CKP sensors are three-wire active devices outputting a clean digital square wave; they require a stable supply voltage and are less sensitive to air-gap variation but intolerant of reversed polarity.
  • Air gap between sensor tip and reluctor/tooth wheel is the critical installation tolerance—typical specs run 0.5–1.5 mm; a gap outside spec produces weak or missing signal and crank-no-start.
  • Connector and pinout keying varies by engine family and generation—same-year engines can use different plug shapes; sensor body length and O-ring diameter must match the block bore to prevent oil leaks and false seating.

Best use cases

  • Daily-driver OEM replacement: choose a sensor with the exact OEM connector keying, resistance value, and mounting depth for your engine code; skip generic 'universal' sensors with adapter harnesses, which add resistance and failure points.
  • Intermittent no-start or stall diagnosis: if the tach drops to zero during cranking or the ECU stores a CKP code only when hot, replace with a Hall-effect sensor if the original was Hall; do not substitute an inductive sensor on a Hall-equipped harness.
  • Performance or engine-swap builds: pick a sensor matched to the reluctor tooth count and ECU trigger expectation (e.g., 36-1, 60-2); skip sensors with unknown tooth-count compatibility, as wrong trigger patterns cause timing errors and backfire.
  • High-vibration off-road or track use: choose sensors with potted electronics and strain-relieved pigtails; skip low-cost open-coil designs where the winding or solder joint fails under vibration.

Buying tips

  • Verify sensor type before ordering: count wires at the connector (2 = inductive, 3 = Hall-effect) and confirm the ECU expects that signal type; mismatched types cause no-start even if the sensor physically fits.
  • Measure the old sensor's mounting depth and air gap with a feeler gauge; replacement tip-to-reluctor gap must fall within the engine's service spec (commonly 0.5–1.5 mm) or signal reliability suffers.
  • Match connector keying and pin count exactly—same engine family across model years can change plug shape; a different keyed connector will not seat and may force a brittle adapter.
  • Check resistance on inductive sensors against the service manual (often hundreds of ohms); a reading far outside spec or open circuit indicates a failed winding, not a wiring fault.

Specs

Sensor TypeInductive (2-wire) vs Hall-effect (3-wire)
Air Gap0.5–1.5 mm typical (engine-specific)
ConnectorKeyed pinout varies by engine code
Mounting DepthMatch block bore and O-ring size

Related searches

What to check before buying

  • Confirm your engine code and model year from the VIN or engine plate; CKP part numbers change by engine variant even within the same model line.
  • Inspect the existing sensor connector for wire count, keying, and pin arrangement; photograph it before ordering to match plug shape and pinout.
  • Measure the sensor bore diameter and mounting depth, and check for a reusable O-ring or seal; a missing or wrong-size seal causes oil leaks at the block.
  • Check reluctor/tooth-wheel condition through the sensor hole; damaged or missing teeth will degrade any new sensor's signal and must be addressed first.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.