Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Coolant Temp Sensor Buying Guide

A coolant temp sensor is a thermistor that reports engine coolant temperature to the ECU for fuel trim, fan control, and gauge output. The key trade-off is OEM-grade calibration and connector sealing versus low-cost universal sensors with loose tolerances. Buy OEM or OE-supplier part numbers (Denso, Delphi, GM Genuine) matched to your engine code; skip generic 'universal' sensors that rely on resistor stacking.

Sensor Type:NTC thermistor, 2-pin or 3-pinThread & Seal:M12x1.5; crush washer or O-ringOE Suppliers:Denso, Delphi, Bosch, NTKSignal Output:ECU temp only vs ECU + gauge
Typical price range$24.99 – $59.95

At a glance

Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

Highlights

  • OE suppliers Denso and Delphi are the factory fitments behind Honda 37870-PNA-003 and GM 12608814 — buy by part number, not by brand marketing.
  • Two-pin NTC thermistors dominate; resistance falls as temperature rises, so a drifted sensor skews cold-start enrichment and radiator fan trigger points.
  • Honda 37870-PJ7-003 and 37870-PNA-003 differ by connector and calibration — cross-referencing by engine and chassis avoids a no-fit or wrong-curve install.
  • Thread pitch and sealing style (M12x1.5 with copper crush washer vs O-ring boss) determine leak-free fit more than sensor brand.

Best use cases

  • Daily-driver Honda/Acura with P0116–P0118 codes: buy the exact Denso 37870-series number for your engine — skip 'universal' 2-wire sensors.
  • GM LS or Ecotec with erratic gauge and fan behavior: use GM Genuine 12608814 (Delphi) rather than a parts-store cross-reference of unknown curve.
  • Performance or swap build needing dash gauge plus ECU input: pick a dual-output or dedicated gauge sender, not a single-signal OEM sensor.
  • Budget repair on an older high-mileage engine: an OE-supplier sensor is still correct; only skip if the harness connector is cracked — then replace pigtail too.

Buying tips

  • Match the OEM part number stamped on the old sensor or the VIN-derived catalog number — same thread, same connector, same resistance curve.
  • Prefer OE suppliers (Denso, Delphi, Bosch, NTK) over unbranded; a thermistor's calibration drift is invisible until fuel trims and fans misbehave.
  • Check connector keyway and pin count: 2-pin NTC and 3-pin dual-output sensors are not interchangeable even if threads match.
  • Replace the crush washer or O-ring with the sensor; reusing a deformed seal is the most common cause of post-install coolant seep.

Specs

Sensor TypeNTC thermistor, 2-pin or 3-pin
Thread & SealM12x1.5; crush washer or O-ring
OE SuppliersDenso, Delphi, Bosch, NTK
Signal OutputECU temp only vs ECU + gauge

Related searches

What to check before buying

  • Confirm engine code and VIN so the catalog returns the exact sensor family (e.g., Honda 37870-PNA-003 vs 37870-PJ7-003).
  • Inspect the existing connector for cracked locking tabs — order a replacement pigtail if damaged.
  • Verify thread size and sealing type at the sensor boss (M12x1.5 crush washer vs O-ring) before ordering.
  • Check cooling system state: low coolant or air pockets mimic sensor failure, so bleed and pressure-test first.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.