Photos from current listings. Actual item, color, and included accessories may vary.
Coolant Temperature Sensor Buying Guide
A coolant temperature sensor (CTS) is a thermistor that reports engine coolant temperature to the ECU for fuel trim, fan control, and gauge operation. The decisive trade-off is OEM-grade thermistor accuracy and connector sealing versus generic low-tolerance parts that drift and trigger P0116/P0118 codes. Buy a genuine OEM or Tier-1 supplier part matched to your engine code; skip unbranded sensors with no resistance curve published.
At a glance
- Category
- Electrical, Sensors & Switches
- Data updated
- Nov 15, 2026
Current offers
Highlights
- OEM/Tier-1 sensors use a negative temperature coefficient (NTC) thermistor with a published resistance curve, typically ~2.5kΩ at 20°C falling to ~200Ω at 90°C for ECU-fed 2-wire types.
- Two-pin NTC sensors feed the ECU and gauge; one-pin senders drive only the dash gauge, so pin count must match the original connector and harness.
- Genuine GM 12608814 (Delphi) and Honda 37870-PNA-003/37870-PJ7-003 (Denso) are direct-fit OEM parts with molded connector seals rated for coolant-tight IP-style sealing.
- Housing material matters: brass or reinforced composite bodies resist glycol attack and thermal cycling better than potted plastic budget units prone to seal failure and coolant wicking.
Best use cases
- Daily-driver repair with a P0116/P0117/P0118 code or erratic temp gauge: pick the OEM part number for your engine (e.g., GM 12608814, Honda 37870-PNA-003) rather than a cross-reference guess.
- Honda/Acura Civic/CL service: use Denso 37870-PJ7-003 or 37870-PNA-003 for the correct 2-pin NTC configuration; skip generic 1-pin senders that won't feed the ECU.
- Performance or swap builds needing gauge-only output: a dedicated 1-pin sender paired with an aftermarket gauge is correct; do not substitute it for the ECU 2-pin sensor.
- Cooling-fan or cold-start drivability faults: replace the ECU-facing 2-pin CTS first; wrong-fit here is a gauge-only sender that leaves fuel and fan logic uncorrected.
Buying tips
- Match the OEM part number and pin count exactly: 2-pin NTC for ECU/gauge logic, 1-pin sender for gauge-only; connector keying differs by engine family.
- Prefer genuine OEM or Tier-1 brands (Delphi, Denso, Bosch, NTK) with a published resistance-vs-temperature table over unbranded units lacking a curve.
- Inspect thread pitch and sealing type — M12x1.5 or M14x1.5 with O-ring or tapered seat — and use a new crush washer or O-ring, never sealant that can contaminate the thermistor.
- Replace the connector pigtail if the original is brittle or coolant-soaked; a corroded harness terminal mimics a failed sensor and skews voltage readings.
Specs
| Sensor Type | NTC thermistor (2-pin ECU / 1-pin gauge) |
|---|---|
| Thread & Seal | M12x1.5 or M14x1.5, O-ring/tapered |
| Brand Tier | OEM (Delphi/Denso) vs generic |
| Resistance Range | ~2.5kΩ @20°C to ~200Ω @90°C |
Related searches
What to check before buying
- Confirm engine code, model year, and original sensor pin count before ordering; the same model can use different CTS part numbers across generations.
- Verify thread size and seal style (O-ring vs tapered) against the existing port, and check clearance to nearby exhaust or hose routing.
- Confirm coolant type (OAT, HOAT, or conventional) is compatible with the sensor body and that the system will be refilled and bled correctly.
- Check that the harness connector and retaining clip are intact and that the ECU expects an NTC curve, not a positive-coefficient or switch-type sender.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.



