Car Gear Picks

Reed Switch Sensor Buying Guide

A reed switch sensor is a sealed glass capsule with ferromagnetic blades that close or open in the presence of a magnetic field, converting motion or proximity into a dry-contact electrical signal without physical actuation. The primary trade-off is glass-encapsulation fragility and contact degradation versus solid-state alternatives: reed switches suit low-power, low-frequency, hermetically sealed logic/switching up to a few watts, while Hall-effect or inductive sensors win above roughly 1 A or in high-vibration environments. The clear decision rule: choose a reed switch only when you need zero standby power, dry-contact isolation, and simple two-wire sensing at low current — otherwise specify a Hall-effect or opto-isolated solution.

Contact Form:Form A / Form B / Form C (SPDT)Switched Load:0.5–1.5 A; 10–50 W maxSensitivity:10–50 AT (lower = more sensitive)Sealing & Mount:Glass capsule; IP67 potted option

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Contact form differences define function: Form A (SPST-NO) is normally open, Form B (SPST-NC) normally closed, and Form C (SPDT) adds a changeover — pick Form A for most proximity triggers and Form C only when you need both states.
  • Power handling is the hard limit: standard glass reed capsules switch roughly 10–50 W and carry 0.5–1.5 A, so any load above about 1 A or 30 V DC needs an interposing relay or MOSFET, not direct switching.
  • Sensitivity is specified in AT (ampere-turns); a 10–15 AT capsule triggers from a small neodymium magnet at a few millimeters, while 30–50 AT parts need a stronger or closer field — match AT to your magnet strength and gap.
  • Hermetic glass sealing gives reed switches a very long mechanical life (10^7–10^8 operations) at low current, but contact welding and glass breakage dominate failures when switching capacitive or inductive loads without suppression.

Best use cases

  • Best fit: door/window intrusion detection, meter pulse counting, and low-voltage position sensing — choose a Form A capsule in a plastic or aluminum housing with a matched magnet and keep switched current under 0.5 A.
  • Best fit: battery-powered or energy-harvesting IoT nodes — the zero-power standby of a reed switch beats a continuously powered Hall sensor, so pair a 10–15 AT capsule with a pull-up resistor into a microcontroller interrupt pin.
  • Wrong fit: direct switching of fans, pumps, solenoids, or LED strips above about 1 A — skip the bare capsule and specify a reed-switch-driven relay module or a Hall-effect/inductive sensor rated for the load.
  • Wrong fit: high-vibration or high-shock installations such as vehicle suspension or industrial motors — glass capsules crack, so use a Hall-effect or magnetoresistive sensor in a potted solid-state package instead.

Buying tips

  • Match AT sensitivity to magnet and gap: a 10–15 AT capsule with a small neodymium disc gives a few-millimeter sensing gap; a 30–40 AT part needs a stronger magnet or a gap under about 2 mm for reliable closure.
  • Check the contact rating line-by-line: a typical capsule is rated around 0.5 A at 100 V DC or 1 A at 24 V DC — derate to about 50–70% for inductive or capacitive loads, or add an RC snubber/MOV across the contacts.
  • Prefer Form C (SPDT) only when the circuit genuinely needs normally closed and normally open outputs; otherwise Form A costs less and removes the risk of the normally closed blade welding under load.
  • For automotive or outdoor use, buy a potted or overmolded reed sensor rated IP67 and specified for the 9–30 V DC range rather than a bare glass capsule, and confirm the magnet is included or matched in strength.

Specs

Contact FormForm A / Form B / Form C (SPDT)
Switched Load0.5–1.5 A; 10–50 W max
Sensitivity10–50 AT (lower = more sensitive)
Sealing & MountGlass capsule; IP67 potted option

Related searches

What to check before buying

  • Measure the actual actuation gap and alignment tolerance between magnet and sensor in your mechanical design; reed sensors typically need the magnet within a few millimeters to a couple of centimeters depending on AT rating and magnet size.
  • Confirm the switched load current and voltage against the capsule datasheet, and add a relay, MOSFET, or snubber if the load exceeds about 1 A or is inductive.
  • Verify the electrical interface your controller expects — dry contact needs a pull-up or pull-down resistor and debounce in firmware, while a 3-wire Hall sensor needs a regulated supply and outputs a logic level.
  • Check environmental sealing and mounting: glass capsules need a protective housing or potting for dust, moisture, and vibration, and the magnet must be oriented to the capsule's sensitive axis for consistent actuation.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.