Car Gear Picks

Piezoelectric Pressure Sensor Buying Guide

A piezoelectric pressure sensor converts mechanical load into a charge or voltage via quartz or PZT ceramic elements, so the core trade-off is dynamic vs static measurement capability. Quartz models excel at high-frequency, high-temperature transients but cannot hold a static reading; ceramic (PZT) models handle lower-frequency and quasi-static loads but drift at temperature extremes. Choose quartz for shock, blast, and combustion dynamics, ceramic for industrial process and quasi-static pressure, and skip any sensor lacking a defined charge amplifier or IEPE interface.

Sensing Element:Quartz vs PZT ceramicOutput Signal:Charge (pC) vs IEPE voltageTemperature Range:Quartz to 350°C; PZT to ~150°CPressure Range:0-5 bar up to 0-1000 bar

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Sensing element: quartz gives wide -200 to 350°C range and sub-microsecond response but AC-coupled only; PZT ceramic extends to quasi-static measurement with lower cost and narrower thermal limits.
  • Output interface: charge-output sensors require an external charge amplifier; IEPE/ICP voltage-output sensors need a constant-current 2-20 mA supply, typically 24 VDC at 4 mA.
  • Key metrics: sensitivity in pC/bar or mV/psi, linearity ±1% FSO, resonant frequency above 5× the measurement bandwidth, and insulation resistance above 10^12 Ω for charge mode.
  • Mounting mechanics: flush-diaphragm and clamp-nut seals preserve frequency response; recessed or threaded-port mounting adds acoustic lag and reduces usable bandwidth.

Best use cases

  • Best fit — engine combustion and ballistic shock: pick quartz charge-mode sensors rated to 350°C with resonant frequency above 100 kHz and a matching charge amplifier; skip PZT ceramic models because thermal drift and lower resonance mask fast transients.
  • Best fit — industrial process and hydraulic monitoring: pick PZT ceramic or IEPE voltage-mode sensors with 4-20 mA or 0-5 V output and a stainless 316L diaphragm; skip bare charge-output models because plant PLCs cannot read pC signals directly.
  • Best fit — acoustic and ultrasound pickups: pick small-aperture piezoelectric sensors with flat response across 10 Hz-100 kHz and integrated IEPE electronics; skip high-pressure industrial transducers because they trade bandwidth for pressure range.
  • Wrong fit — static or slowly changing pressure: any pure piezoelectric sensor fails here; specify a strain-gauge or capacitive pressure transmitter instead because piezoelectric elements leak charge under constant load.

Buying tips

  • Measure the expected pressure range and add 50% headroom: a 0-100 bar application should use a 150 bar-rated sensor, since overrange shocks above the rated maximum permanently depolarize ceramic elements.
  • Verify the charge amplifier or IEPE supply is included in the signal chain: a charge-mode sensor without a matching pC-to-voltage amplifier delivers an unusable high-impedance signal.
  • Match resonant frequency to at least five times the highest frequency of interest; a 10 kHz measurement needs a sensor with a resonant frequency above 50 kHz to avoid amplitude error.
  • Confirm thread and seal standard before ordering: M5×0.5, 1/4-28 UNF, and M10×1 are the common mounting threads, and flush-diaphragm seals need the correct copper or PTFE gasket to avoid leakage.

Specs

Sensing ElementQuartz vs PZT ceramic
Output SignalCharge (pC) vs IEPE voltage
Temperature RangeQuartz to 350°C; PZT to ~150°C
Pressure Range0-5 bar up to 0-1000 bar

Related searches

What to check before buying

  • Confirm the mounting thread (M5×0.5, 1/4-28 UNF, M10×1) and available clearance depth in your port or fixture.
  • Check the operating temperature at the sensor diaphragm, not ambient: quartz handles 350°C, PZT ceramic typically tops out near 120-150°C.
  • Verify signal-conditioning availability: charge amplifier for pC output, or a 2-20 mA IEPE source for voltage output, and confirm cable connector type (BNC, 10-32, M4).
  • Check ingress protection and medium compatibility: stainless 316L or Inconel diaphragm for corrosive fluids, IP67 or better for washdown environments.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.