Particulate Matter Sensor Buying Guide
A particulate matter (PM) sensor is a solid-state or optical module that quantifies airborne particles (PM1.0, PM2.5, PM10) and outputs a calibrated signal for air-quality monitoring, HVAC control, or automotive emissions systems. The core trade-off is optical/electrochemical sensing architecture versus calibration stability and interface compatibility: laser-scattering modules deliver real-time mass concentration, while automotive PM sensors use resistive or electrochemical elements for soot detection in exhaust streams. The decision rule is simple: match the sensing principle and output protocol to your host system, and reject any module lacking a published calibration curve or standardized interface.
At a glance
- Price range
- Price range not synced yet
- Category
- Electrical, Sensors & Switches
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Laser-scattering optical PM sensors (e.g., Plantower PMS5003, Sensirion SPS30) measure particle counts via photodiode and convert to mass concentration; they require fan-driven airflow and are sensitive to humidity above 85% RH.
- Automotive PM sensors (e.g., Bosch, Continental) use resistive soot sensing in exhaust after-treatment and communicate via CAN or SENT protocol — they are not interchangeable with ambient air-quality modules.
- UART, I2C, and PWM are the three common output interfaces; UART full-duplex is standard on PMS-series modules, while I2C is typical on Sensirion and many low-power MEMS sensors.
- PM2.5 accuracy is typically specified as ±10% of reading or ±10 µg/m³ (whichever is greater) for calibrated optical modules; uncalibrated modules drift beyond that threshold within months.
Best use cases
- Best fit: Indoor air-quality monitors and smart-home builds — choose a laser-scattering module with UART or I2C output and a published PM2.5 calibration curve; skip automotive resistive sensors.
- Best fit: Automotive exhaust or diesel particulate filter (DPF) monitoring — select a CAN/SENT-output soot sensor rated for exhaust temperature and pressure; skip ambient optical modules that cannot survive >80°C.
- Best fit: HVAC or building automation — use a duct-mount PM sensor with 0-10V or Modbus output and IP-rated housing; skip bare PCB modules without environmental sealing.
- Wrong fit: Outdoor continuous monitoring without a weatherproof enclosure and hydrophobic filter — bare optical sensors clog and fail within weeks; choose an IP65-rated integrated sensor instead.
Buying tips
- Match the output protocol to your controller: UART (PMS5003) for Arduino/ESP32, I2C (SPS30) for Raspberry Pi and low-pin-count designs, and CAN/SENT for automotive ECUs — protocol mismatch requires a converter board.
- Check the particle size range: PM2.5-only sensors are cheaper but miss PM10 and PM1.0; choose a 3-channel (PM1.0/2.5/10) module if you need comprehensive air-quality indexing.
- Verify the calibration standard: sensors calibrated to ISO 12103-1 A1 test dust or equivalent are traceable; modules without a stated calibration reference should be avoided for regulatory or health-related reporting.
- For automotive DPF applications, confirm the sensor is rated for 12V/24V system voltage and exhaust temperatures up to 800°C; ambient optical sensors are rated for 0-50°C and will fail immediately in exhaust streams.
Specs
| Sensing Principle | Laser scattering vs resistive soot |
|---|---|
| Output Interface | UART / I2C / PWM / CAN / SENT |
| Particle Range | PM1.0 / PM2.5 / PM10 (µg/m³) |
| Operating Temp | 0-50°C ambient / 800°C exhaust |
Related searches
What to check before buying
- Measure your enclosure or duct opening: optical modules need a 20-30 mm airflow path and a fan; confirm the module footprint fits your housing before ordering.
- Confirm your controller's logic level: 3.3V vs 5V UART — mismatched logic levels damage the sensor; use a level shifter if necessary.
- For automotive use, verify the vehicle's communication bus (CAN 2.0A/B or SENT) and sensor thread size (M20×1.5 or M18×1.5) against the exhaust bung.
- Check environmental ratings: ambient sensors require <85% RH and <50°C; automotive sensors require IP6K9K and 800°C exhaust rating — never interchange them.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
