Car Gear Picks

Magnetic Pickup Sensor Buying Guide

A magnetic pickup sensor (MPU) is a variable-reluctance generator that converts passing ferrous teeth or gear teeth into an AC voltage pulse for tachometers, ignition, speedometers, and industrial counters. The primary trade-off is passive VR simplicity versus active Hall-effect signal conditioning: VR pickups need adequate air gap and target speed and produce amplitude that scales with RPM, while Hall sensors deliver clean square waves down to zero speed but require a supply voltage. Choose passive VR only for high-temperature, high-vibration, no-power environments with known target geometry; choose active Hall for low-speed or digital-input compatibility.

Sensor Type:Passive VR vs Active HallOutput Signal:AC sine (VR) vs square wave (Hall)Supply Voltage:None (VR) / 5-24 V DC (Hall)Thread / Mount:M12×1, M16×1.5, 5/8-18 UNF

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Passive variable-reluctance pickups generate 0.5–200 V AC peak-to-peak, with output amplitude proportional to tooth speed; below roughly 50–100 RPM the signal may be too weak for the tachometer.
  • Active Hall-effect sensors output a defined square wave (typically 0–5 V or 0–12 V) and operate from zero speed, but demand a stable supply (5 V, 12 V, or 24 V) and correct polarity.
  • Output connector types vary by segment: two-wire flying lead for VR, three-wire (supply, ground, signal) for Hall; waterproof IP67 or IP68 ratings matter in engine bays and wet industrial areas.
  • Target geometry determines signal quality: tooth count, tooth profile, and air gap (commonly 0.5–1.5 mm for VR, 0.5–2 mm for Hall) must match the sensor's design; a missing or damaged tooth produces a dropout.

Best use cases

  • Best fit for passive VR: ignition tachometers on carbureted or distributor engines, gear-tooth speed sensing on transmissions, and high-temperature exhaust-side applications where no supply voltage is available.
  • Best fit for active Hall: crankshaft or camshaft speed sensors feeding an ECU, low-speed conveyor or wheel speed sensing, and any system requiring a clean digital pulse at near-zero RPM.
  • Wrong fit: using a passive VR sensor with a digital tachometer that expects a square wave without a signal conditioner; also wrong to install a Hall sensor on a non-ferrous target (aluminum, plastic) with no magnetic interruption.
  • Wrong fit: selecting a pickup without matching the threaded body diameter (common M12×1, M16×1.5, 5/8-18 UNF) and mounting thread to the existing bracket—thread adapters are rare and often unavailable for a given sensor.

Buying tips

  • Match the sensor's output type to the receiving device: VR pickups produce AC that requires a tachometer with a VR input or an external signal conditioner; Hall sensors output a square wave that most digital tachometers and ECUs accept directly.
  • Size the threaded body to the mounting hole: common metric threads are M12×1 and M16×1.5; common imperial is 5/8-18 UNF. Measure the existing bracket bore and thread pitch before ordering—do not assume a universal fit.
  • Confirm the target tooth count and air gap: the sensor's voltage output at a given RPM scales with tooth count and gap. For VR pickups, a 36-1 trigger wheel with 1 mm gap is a typical baseline; for Hall, verify the target is ferrous and the gap is within the sensor's rated range.
  • For high-vibration or high-temperature installations, choose a potted or epoxy-sealed body rated IP67 or higher and a lead wire with a high-temperature jacket (e.g., PTFE or silicone) rather than PVC.

Specs

Sensor TypePassive VR vs Active Hall
Output SignalAC sine (VR) vs square wave (Hall)
Supply VoltageNone (VR) / 5-24 V DC (Hall)
Thread / MountM12×1, M16×1.5, 5/8-18 UNF

Related searches

What to check before buying

  • Measure the mounting thread: diameter and pitch (e.g., M12×1, M16×1.5, 5/8-18 UNF) and confirm the sensor body length clears the bracket and target without bottoming out.
  • Verify target material is ferrous (steel or iron) and measure the air gap with a feeler gauge; ensure it falls within the sensor's rated range (typically 0.5–1.5 mm for VR, 0.5–2 mm for Hall).
  • Check supply voltage and wiring: Hall sensors require a regulated supply (5 V, 12 V, or 24 V) and three wires (Vcc, GND, signal); passive VR uses two wires and no supply.
  • Confirm connector type and harness length: flying leads, Deutsch DT, Weather Pack, or M12 circular connectors must mate with the existing harness; add a waterproof connector if splicing in a wet area.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.