Magnetic Field Sensor Buying Guide
Magnetic field sensors convert magnetic flux density into an electrical signal, and the core buying decision is choosing the right sensing technology (Hall effect, magnetoresistive, or fluxgate) for your required range, resolution, and environment. The primary trade-off is sensitivity versus saturation range: high-sensitivity sensors resolve weak fields but saturate in strong ones, while wide-range sensors sacrifice microtesla resolution. The decision rule is simple: match the sensor's technology and package to the field strength, frequency, and temperature you will actually encounter, not to the lowest headline sensitivity.
At a glance
- Price range
- Price range not synced yet
- Category
- Electrical, Sensors & Switches
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Hall-effect sensors dominate general-purpose DC and low-frequency field measurement, with linear ratiometric outputs typically spanning ±50 to ±2000 gauss and bandwidths from DC to 20-100 kHz.
- Magnetoresistive (AMR/GMR/TMR) sensors deliver 10-100x better sensitivity than Hall devices, resolving fields below 1 microtesla but saturating at only a few gauss, suiting compass and current-sense designs.
- Fluxgate sensors reach sub-nanotesla resolution and near-zero offset drift, making them the reference choice for geomagnetic and navigation-grade measurement at higher cost and power.
- Digital output tiers (I2C/SPI) with 12-16 bit ADCs and factory calibration eliminate external signal conditioning, while analog ratiometric parts require a stable supply reference for accuracy.
Best use cases
- Best fit: rotor position or BLDC motor commutation — pick a latching or bipolar Hall switch with defined operate/release gauss thresholds and an automotive temperature rating; skip high-sensitivity magnetoresistive parts that saturate near the magnet.
- Best fit: electronic compass or weak-field anomaly detection — choose an AMR or fluxgate sensor with sub-microtesla resolution and hard/soft-iron calibration support; skip linear Hall sensors whose noise floor masks Earth's 25-65 microtesla field.
- Best fit: non-invasive current sensing — select a core-based Hall or fluxgate current sensor rated for the conductor's ampacity and isolation voltage; skip bare Hall ICs without a concentrator core for low-current measurement.
Buying tips
- Confirm the field range covers your expected maximum plus 30% headroom; a sensor rated to ±1000 gauss saturates permanently above that and cannot be recalibrated for stronger magnets.
- Match output type to your interface: ratiometric analog needs a stable ADC reference, while I2C/SPI digital parts need pull-up resistors and correct bus voltage (commonly 1.8-5.5 V).
- Check the temperature coefficient of sensitivity, typically -0.1% to -0.3% per degree C for Hall devices; precision designs require factory-calibrated or temperature-compensated tiers.
- For battery-powered nodes, compare supply current: Hall switches draw microamps, linear Halls milliamps, and fluxgates tens of milliamps, directly setting battery life.
Specs
| Sensing Technology | Hall / AMR / GMR / TMR / Fluxgate |
|---|---|
| Field Range | ±1 gauss to ±3000 gauss |
| Output Interface | Analog ratiometric / I2C / SPI / Switch |
| Supply Voltage | 1.8-5.5 V DC typical |
Related searches
What to check before buying
- Measure or estimate the maximum magnetic flux density at the sensor location with a gaussmeter or datasheet magnet curve before selecting sensitivity.
- Verify package and mounting: through-hole TO-92 for prototyping versus SMD SOT-23 or QFN for production, with solder reflow profiles within the sensor's rated temperature.
- Confirm supply voltage and output logic levels match your microcontroller or PLC input, including open-drain versus push-pull output configuration.
- Check operating temperature range against the environment; automotive-grade parts are rated -40 to 150 C, commercial parts often only 0 to 70 C.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
