Linear Position Sensor Buying Guide
A linear position sensor converts straight-line travel into an electrical signal for feedback, measurement, or limit detection. The core trade-off is measurement principle versus environment: resistive potentiometers are cheap but wear, while inductive, magnetostrictive, and LVDT types trade higher cost for non-contact durability. The decision rule is simple: match the sensing technology and ingress rating to your stroke length, cycle count, and contamination exposure—not to the lowest unit price.
At a glance
- Price range
- Price range not synced yet
- Category
- Electrical, Sensors & Switches
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Resistive (potentiometer) sensors offer the lowest cost and simple analog output, but the wiper contact wears; rated life is typically 1–10 million cycles depending on grade.
- Inductive and magnetostrictive sensors are non-contact, delivering 50 million to infinite cycle life with better shock and vibration tolerance for industrial and automotive use.
- LVDT sensors provide the highest linearity and resolution (sub-micron repeatability) but require AC excitation and signal conditioning, adding cost and wiring complexity.
- Ingress protection separates viable outdoor/automotive units from lab parts: IP67 handles washdown and temporary immersion, while IP69K adds high-pressure steam cleaning resistance.
Best use cases
- Pick a sealed IP67 magnetostrictive or inductive sensor for mobile hydraulics, suspension travel, or outdoor automation—skip open-frame potentiometers that ingest dust and water.
- Use a compact potentiometer or Hall-effect sensor for budget-friendly indoor actuator feedback, 3D printer beds, or hobby robotics where cycle counts stay under a few million.
- For automotive throttle, pedal, or ride-height sensing, select a Hall-effect or inductive sensor with ratiometric output and OEM-style connectors; generic industrial potentiometers lack the vibration and temperature ratings.
Buying tips
- Match stroke length to your actual travel plus 10–20% headroom; a sensor rated for 100 mm used on a 90 mm stroke leaves margin for mounting tolerance and overtravel.
- Check output type against your controller: 0–10 V, 4–20 mA, ratiometric 0.5–4.5 V, or PWM. A 4–20 mA loop resists EMI over long cable runs better than voltage output.
- For high-cycle applications (presses, valves, dampers), specify non-contact inductive or magnetostrictive types rated for 50 million+ cycles; potentiometers wear out and cause drift.
- Verify temperature and shock ratings: automotive/industrial use demands –40 to +125 °C and 50 g shock tolerance; lab-grade LVDTs often top out at 70 °C.
Specs
| Sensing Technology | Potentiometer / Inductive / LVDT / Magnetostrictive |
|---|---|
| Stroke Range | 10–1000 mm typical; 50–300 mm common |
| Output Signal | 0–10 V / 4–20 mA / 0.5–4.5 V ratiometric / PWM |
| Ingress Protection | IP54 to IP69K (IP67 minimum outdoor) |
Related searches
What to check before buying
- Measure your maximum travel and mounting envelope; confirm the sensor body plus rod or magnet fits without bottoming out at either end of the stroke.
- Confirm supply voltage and output signal match your PLC, ECU, or DAQ—24 VDC 4–20 mA is common in industrial, 5 V ratiometric in automotive.
- Check connector and cable standard: M12, Deutsch DT, or flying leads; ensure the mating harness or connector kit is available before ordering.
- For outdoor or washdown use, verify IP67 or IP69K and chemical compatibility of the housing (316 stainless or anodized aluminum) with your environment.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
