Car Gear Picks

Exhaust Camshaft Position Sensor Buying Guide

An exhaust camshaft position sensor is a Hall-effect or variable-reluctance device that reports camshaft phasing to the ECU for sequential fuel injection, VVT actuation, and misfire detection. The core trade-off is OEM-style sealed Hall sensor with correct connector keying versus generic inductive pickups with loose tolerances that cause cold-start and P0014/P0011 faults. Buy OEM-equivalent Hall units with factory-style pigtails and the correct air gap specification; skip unsealed generic sensors and any part without a matching connector pinout.

Sensor Type:Hall-effect (3-wire) vs inductive (2-wire)Connector Family:GT150 / Junior Timer / USCARAir Gap:0.5–1.5 mm typicalSeal Material:Fluorosilicone / Viton O-ring

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Hall-effect sensors dominate modern VVT engines and output a digital square wave; variable-reluctance (inductive) types output an AC sine wave and require a minimum cranking RPM to trigger.
  • Sensor air gap typically runs 0.5–1.5 mm; incorrect air gap or a worn reluctor ring drops signal amplitude and triggers intermittent P0340/P0345 codes.
  • Genuine OEM units use glass-filled PA66 housings, fluorosilicone O-rings, and gold-plated terminals; generic units often use plain brass pins and nitrile O-rings that fail with heat cycling.
  • Integrated pigtail length and connector keying vary by engine family—match the OEM connector code (e.g., 3-pin GT150 vs 2-pin Junior Timer) rather than splicing a universal plug.

Best use cases

  • Best fit: a VVT-equipped engine throwing P0014, P0011, or P0340/P0345 with rough idle or hard cold starts—replace with an OEM-equivalent sealed Hall sensor and new O-ring.
  • Best fit: a high-mileage engine where the sensor is original and the reluctor ring shows wear—pair the new sensor with a visual reluctor inspection and correct air-gap check.
  • Wrong fit: choosing a universal 2-wire inductive sensor for a 3-wire Hall circuit—pin count, waveform type, and ECU trigger logic are incompatible and will not start or run correctly.
  • Wrong fit: buying a sensor without a matching connector pigtail or terminal kit when the factory harness plug is cracked—sensor alone will not resolve intermittent connection faults.

Buying tips

  • Count the pins on the original sensor: 2-pin inductive vs 3-pin Hall is the first compatibility gate; a 3-pin Hall sensor will not work in a 2-pin inductive circuit.
  • Match the OEM connector family (GT150, Junior Timer, USCAR) and pigtail length to the harness; splicing a universal plug without a sealed crimp introduces moisture and intermittent faults.
  • Choose a sensor with a fluorosilicone or Viton O-ring for oil-exposed locations; nitrile O-rings harden and leak within a few heat cycles.
  • Verify the air-gap specification for your engine (commonly 0.5–1.5 mm) and confirm the sensor body depth matches the factory mounting boss—too deep risks reluctor contact.

Specs

Sensor TypeHall-effect (3-wire) vs inductive (2-wire)
Connector FamilyGT150 / Junior Timer / USCAR
Air Gap0.5–1.5 mm typical
Seal MaterialFluorosilicone / Viton O-ring

Related searches

What to check before buying

  • Confirm engine code and bank/position (exhaust vs intake) from the VIN or engine tag—intake and exhaust sensors often share a housing but differ in connector keying and phasing.
  • Inspect the factory harness connector for cracked locks, corrosion, or pushed pins before ordering; a damaged pigtail requires a repair kit, not just the sensor.
  • Measure the mounting boss depth and reluctor clearance; ensure the new sensor's insertion depth matches the OEM unit rather than bottoming out on the reluctor.
  • Check oil condition and cam phaser health—sludge or a failing phaser can mimic sensor failure and will destroy a replacement sensor if not addressed.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.