Car Gear Picks

Eddy Current Sensor Buying Guide

Eddy current sensors are non-contact inductive probes that measure displacement, position, vibration, and material thickness by sensing impedance changes in a conductive target. The primary trade-off is probe diameter versus resolution and linear range: larger coils give longer range but coarser resolution, while smaller coils resolve microns at the cost of standoff distance. The decision rule is simple: match probe size and cable length to the target material and controller input standard (eddy-current driver vs. generic proximity switch), and reject any sensor without a specified linearity and temperature-drift figure.

Probe Diameter:2-20 mm coil (range scales with size)Output Type:Analog 4-20 mA / 0-10 V vs switchLinearity:≤±0.5% FS (industrial grade)Target Material:Ferrous strongest; non-ferrous reduced

At a glance

Price range
Price range not synced yet
Category
Electrical, Sensors & Switches
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Probe diameters typically run 2 mm to 20 mm; smaller coils achieve sub-micron resolution but linear ranges under 0.5 mm, while 20 mm probes reach several millimeters of standoff.
  • Output architecture splits into analog current/voltage drivers (4-20 mA, 0-10 V) for displacement and frequency/switch outputs for presence detection—analog drivers require a matched oscillator/demodulator unit.
  • Linearity and resolution are specified as % of full-scale range; industrial-grade probes publish ≤±0.5% linearity and thermal drift in %FS/°C, which generic inductive proximity switches do not.
  • Target material matters: ferromagnetic steel yields the strongest signal, while aluminum, copper, and austenitic stainless require calibration or reduced range, and non-conductive targets cannot be sensed at all.

Best use cases

  • Best fit: rotating-machinery vibration and shaft displacement monitoring—pick an analog-driver probe with ≤±0.5% linearity and a matched controller; skip generic proximity switches that only give on/off.
  • Best fit: high-speed position or runout measurement on conductive targets—choose a small-diameter (2-5 mm) probe with sub-micron resolution and short cable; skip long-cable versions that add capacitance and noise.
  • Best fit: presence/edge detection on production lines—a standard eddy-current proximity sensor with NPN/PNP switch output and IP67 housing works; skip precision analog drivers that cost more and need a separate amplifier.
  • Wrong fit: measuring plastic, glass, or wood targets—eddy current sensors require conductive material; use capacitive or laser sensors instead.

Buying tips

  • Match probe diameter to required range: linear range is roughly 20-50% of coil diameter, so a 5 mm probe typically covers about 1-2.5 mm of measurement span.
  • Confirm the driver/controller input: analog eddy-current probes need a dedicated oscillator-demodulator with the correct excitation frequency; a 4-20 mA probe will not run on a 0-10 V input without conversion.
  • Check cable length and connector standard: extension cables add capacitance that shifts calibration, so keep total cable under the manufacturer's specified maximum and use the same connector series (e.g., LEMO, BNC, M12).
  • For high-temperature environments, select probes rated above the actual surface temperature—standard probes top out near 120-150 °C, while high-temp variants with separate coils reach 200 °C or more.

Specs

Probe Diameter2-20 mm coil (range scales with size)
Output TypeAnalog 4-20 mA / 0-10 V vs switch
Linearity≤±0.5% FS (industrial grade)
Target MaterialFerrous strongest; non-ferrous reduced

Related searches

What to check before buying

  • Target material and geometry: confirm the target is conductive and large enough relative to probe diameter (typically at least 3× the coil diameter) to avoid edge effects.
  • Mounting and clearance: measure the available standoff distance and thread size (common M5, M8, M12, or 1/4-28) against the probe body and cable exit.
  • Electrical environment: verify supply voltage (commonly 12-24 V DC), output type (analog vs. switch), and shielding against nearby motors or VFDs.
  • Companion parts: budget for a matched driver/amplifier, extension cable, and mounting bracket—probes are rarely usable standalone.

FAQ

All Electrical, Sensors & Switches buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.