Line Fuel Pump Buying Guide
An in-line fuel pump is a remote-mount electric pump that sits in the fuel line between tank and engine, used to restore or upgrade fuel delivery on older cars, carbureted builds, and return-style EFI conversions. The core trade-off is flow/pressure capability versus pump architecture: brushed roller-vane pumps are cheap but short-lived, while brushless or turbine designs deliver the stable pressure and longevity needed for EFI. The decision rule is simple: match pump deadhead pressure and flow to your fuel system's demand, and buy only pumps rated for continuous duty at your voltage and fuel type.
At a glance
- Price range
- Price range not synced yet
- Category
- Engine, Exhaust & Fuel System Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Flow ratings must be read at a specific pressure: a pump rated 255 LPH at 40 psi may flow far less at 60 psi, so compare flow at your actual rail pressure.
- Turbine and brushless pumps run quieter and last longer than brushed roller-vane designs, which shed brush material and lose pressure over time.
- External pumps are pushers, not pullers: mounting above the tank or far from it causes cavitation and vapor lock, so mount low and near the tank.
- Pressure and flow are separate ratings: an EFI pump must hold the regulator's base pressure plus boost rise, while carbureted pumps should stay under 7 psi without a regulator.
Best use cases
- Best fit: carbureted V8 or older engine with a mechanical pump failure — choose a low-pressure (4-7 psi) external pump with a return-style regulator or a bypass regulator to avoid flooding.
- Best fit: EFI swap or high-power build needing more fuel — choose an in-line EFI pump rated for your target horsepower at your base pressure plus boost, with a return line and proper filtration.
- Wrong fit: modern returnless EFI vehicles with PWM-controlled in-tank modules — an in-line pump bypasses the control strategy and trips codes; replace the in-tank module or use a proper surge tank setup.
Buying tips
- Size flow using brake-specific fuel consumption: gasoline needs about 0.5 lb/hp/hr, so a 500 hp engine requires roughly 250 lb/hr, or about 40 gallons per hour at 6 lb/gal.
- Match pressure to fuel system: carbureted pumps should be 4-7 psi; port EFI typically 40-60 psi base; returnless systems need a pump rated above the highest commanded pressure.
- Choose a pump with an integrated check valve and compatible with gasoline or E85; ethanol-rated pumps use different seals and motor materials than gasoline-only units.
- Mount the pump below the lowest fuel level and within a short distance of the tank, and use a 10-micron post-pump filter for EFI or a 100-micron pre-filter to protect the pump.
Specs
| Pump Architecture | Turbine / Brushless vs Roller-Vane Brushed |
|---|---|
| Flow Rating | 100-450 LPH at rated pressure |
| Operating Pressure | 4-7 psi carb / 40-80 psi EFI |
| Fuel Compatibility | Gasoline / E85 / Methanol grades |
Related searches
What to check before buying
- Measure fuel line diameter and fitting type at the mounting location: most in-line pumps use 3/8-inch NPT or barbed fittings, and adapters must match your hard line or hose size.
- Confirm electrical capacity: a 255 LPH EFI pump can draw 15-20 amps at full load, so verify alternator output and use a relay with a fused 12-gauge feed directly from the battery.
- Check fuel type and tank material: E85 and methanol require ethanol-compatible pumps and hoses; older rubber lines may degrade and send debris into a new pump.
- Verify mounting location has clearance from exhaust and moving suspension parts, and that the pump body is isolated with rubber mounts to reduce noise and vibration.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
