Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Honda Accord Ignition Coil Buying Guide

An ignition coil is the step-up transformer that converts 12V battery voltage into the 20–40 kV spark that ignites the air-fuel mixture in each cylinder. The core trade-off is OEM-grade epoxy-potted coils with matched primary resistance versus cheap dry-wound coils that fail from heat and vibration. The decision rule: buy coils whose primary resistance and connector keying match your exact engine code (K24W, J35, L15B) and replace all four or six at once rather than mixing new and aged coils.

Coil Type:Coil-on-plug (COP), individual per cylinderSet Quantity:4 coils (I4) / 6 coils (V6)Primary Resistance:0.5–1.5 ohms (OEM spec)Construction:Epoxy-potted with silicone boot
Typical price range$86.99

At a glance

Category
Engine, Exhaust & Fuel System Parts
Data updated
Nov 15, 2026

Current offers

Highlights

  • Honda K24W 2.4L four-cylinder engines use four identical coil-on-plug coils; J35 V6 engines use six, and mixing brands across cylinders causes uneven spark energy.
  • Coil primary resistance typically specs at 0.5–1.5 ohms and secondary at 5–15 kΩ; a coil reading outside these ranges or with cracked epoxy is failed.
  • OEM-style coils use epoxy potting and silicone boots; budget dry-wound coils arc through the boot and misfire under load within tens of thousands of miles.
  • Honda revised coil part numbers across Accord generations (2013–2017 vs 2018–2022), so connector keying and mounting bolt spacing differ and coils are not interchangeable.

Best use cases

  • Best fit: replace all four coils on a 2013–2017 Accord 2.4L at the first P030x misfire code with epoxy-potted coils matched to the K24W engine code.
  • Best fit: V6 Accord owners should buy six coils as a set; replacing one coil on a J35 leaves five aged coils that will misfire shortly after.
  • Wrong fit: do not install CR-V or Acura ILX coils on an Accord without confirming the same engine code and connector keying — listing fitment text is not a substitute for part-number matching.
  • Wrong fit: skip dry-wound budget coils for turbocharged or high-mileage engines; heat soak accelerates insulation breakdown and repeat misfires.

Buying tips

  • Match the coil to the engine code stamped on the block (K24W, J35, L15B), not just the model year, because Honda used multiple coil variants across trims.
  • Buy coils in complete sets of four (I4) or six (V6) so all cylinders share identical spark energy and aging behavior.
  • Confirm the coil boot length and connector pin count match the original harness plug; short boots cause arc-through and long boots stress the plug terminal.
  • Prefer coils with epoxy potting and OEM-equivalent primary resistance (0.5–1.5 ohms) over dry-wound designs; measure resistance with a multimeter before installation.

Specs

Coil TypeCoil-on-plug (COP), individual per cylinder
Set Quantity4 coils (I4) / 6 coils (V6)
Primary Resistance0.5–1.5 ohms (OEM spec)
ConstructionEpoxy-potted with silicone boot

Related searches

What to check before buying

  • Read the engine code on the block and the original coil part number before ordering; Accord 2.4L and 3.5L coils are not interchangeable.
  • Count cylinders — four coils for I4, six for V6 — and order the complete set plus new spark plugs gapped to Honda spec.
  • Inspect the coil boot and connector for oil contamination from a leaking valve cover gasket; replace the gasket before installing new coils.
  • Verify the replacement coil's primary resistance with a multimeter and confirm the connector keying matches the factory harness plug.

FAQ

All Engine, Exhaust & Fuel System Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.