Hellcat Engine Buying Guide
The Hellcat engine is a supercharged 6.2L Hemi V8 offered in crate, pull-out, and turn-key configurations, with the core trade-off being forged-internals reliability versus budget-friendly take-off condition. Buyers must choose between a factory-rated 707 hp long block and higher-output Redeye/Demon variants, while verifying the engine is a genuine Hellcat casting rather than a standard 5.7/6.4 Hemi with a bolt-on blower.
Displacement:6.2L supercharged V8 (376 cu in)Power Tier:707 hp base / 797–840 hp RedeyeSupercharger:2.4L IHI (2.7L on Redeye)Internals:Forged pistons, rods, crank
At a glance
- Price range
- Price range not synced yet
- Category
- Engine, Exhaust & Fuel System Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Genuine Hellcat blocks are cast with 'Hellcat' or '6.2L' identifiers and use forged pistons, rods, and crank; standard 5.7/6.4 Hemi internals are hypereutectic and fail above 600 hp.
- The 2.4L IHI twin-screw supercharger is the defining hardware; Redeye and Demon engines step to a 2.7L blower and stronger pistons/rods for 797–840 hp.
- Crate engines ship as long blocks with intake, supercharger, and harness; pull-outs often arrive as partial assemblies missing the ECU, fuel rails, or accessory drive.
- All Hellcat variants require premium fuel (91+ octane), a high-volume fuel pump, and a TR-6060 or 8HP90 transmission rated for the torque.
Best use cases
- Best fit: A resto-mod or muscle car build targeting 700–800 hp — choose a complete crate engine with ECU and harness to avoid sourcing rare factory connectors.
- Wrong fit: A daily driver or budget swap in a V6/5.7 chassis — skip the Hellcat and use a 6.4 Hemi or LS swap; the Hellcat's fuel system, cooling, and transmission demands triple the install cost.
- Best fit: A drag-race or show car where provenance matters — pick a documented pull-out with VIN and compression-test sheet rather than an unbranded long block.
- Wrong fit: A truck or off-road rig needing low-end torque — skip the Hellcat's peaky supercharged curve and choose a 6.4 Hemi or diesel for durability under load.
Buying tips
- Demand a compression test and leak-down numbers: healthy Hellcat cylinders read 150–180 psi with less than 10% leak-down; anything lower signals ring or valve wear.
- Verify the supercharger snout and pulley: stock 2.4L blowers use a 3.10-inch pulley; a smaller pulley without a tune and fuel upgrades risks detonation and piston failure.
- Match the transmission torque rating: the 8HP90 automatic handles 664 lb-ft, while the TR-6060 manual is rated for 600 lb-ft — a built 8HP90 or T-56 Magnum is required above 800 hp.
Specs
| Displacement | 6.2L supercharged V8 (376 cu in) |
|---|---|
| Power Tier | 707 hp base / 797–840 hp Redeye |
| Supercharger | 2.4L IHI (2.7L on Redeye) |
| Internals | Forged pistons, rods, crank |
Related searches
What to check before buying
- Measure your engine bay: Hellcat long blocks are approximately 30 inches wide with the supercharger and require a minimum 26-inch radiator-to-firewall clearance.
- Confirm fuel system capacity: a Hellcat needs at least a 450 LPH in-tank pump and -8 AN feed line; stock 3/8-inch lines and 255 LPH pumps starve the engine at high RPM.
- Verify hood clearance: the supercharger and intake hat add roughly 4 inches over a standard Hemi; a cowl hood or 2-inch body lift is typically required.
- Check emissions and legal status: Hellcat crate engines are sold for off-road use only and will not pass OBD-II emissions testing in most states without a certified swap package.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
