Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Head Gasket Buying Guide

A head gasket is the critical seal between the engine block and cylinder head, containing combustion pressure, coolant, and oil. The primary trade-off is between original-style composite gaskets and modern multi-layer steel (MLS) designs, with MLS being mandatory for aluminum blocks and forced induction. The clear decision rule: match gasket material and thickness to your engine's block/head material and OEM spec—never substitute a composite gasket where MLS is specified.

Gasket Type:MLS vs CompositeHead Bolt Type:TTY vs Reusable StudsCompressed Thickness:0.5-1.5 mm OEMBore Oversize:Std, +0.5 mm, +1.0 mm
Typical price range$91.99 – $854.99

At a glance

Category
Engine, Exhaust & Fuel System Parts
Data updated
Nov 15, 2026

Current offers

Highlights

  • MLS (multi-layer steel) gaskets use 3-5 embossed stainless steel layers with elastomer coatings, required for aluminum heads and high-compression or boosted engines.
  • Composite gaskets (graphite/fiber) suit older cast-iron engines and low-compression naturally aspirated builds but fail under boost or with aluminum block/head thermal expansion.
  • Head bolt type determines gasket survival: torque-to-yield (TTY) bolts stretch once and must be replaced; reusable studs require retorquing sequences and higher clamp load.
  • Gasket thickness (compressed) changes compression ratio and piston-to-valve clearance; OEM thickness is typically 0.5-1.5 mm and must be matched unless engine is rebuilt for a different quench.

Best use cases

  • Best fit: stock or mildly modified aluminum-head engines (e.g., Chevy 1.4L, GM 3.6L, BMW N63) require an MLS gasket with new TTY bolts—skip composite gaskets and reused bolts.
  • Best fit: high-mileage cast-iron V8 or V6 with no forced induction can use a quality composite gasket if OEM specified, but MLS is a safe upgrade for durability.
  • Wrong fit: using a thick MLS gasket to 'fix' a warped head or deck without machining—gasket thickness cannot correct surface flatness beyond 0.05 mm.
  • Wrong fit: buying a full head gasket kit with timing chain/valve parts when only the gasket failed—match kit contents to actual failure (compression vs coolant vs oil leak).

Buying tips

  • Always replace head bolts with the gasket: TTY bolts yield at installation and lose clamp load if reused, causing immediate gasket failure.
  • Measure head and block flatness with a straight edge and feeler gauge; maximum allowable out-of-flatness is typically 0.05 mm (0.002 in) for MLS and 0.1 mm for composite.
  • Match gasket bore size to cylinder overbore: gaskets are available in standard and +0.5 mm/+1.0 mm oversizes; an oversized gasket on a standard bore reduces compression sealing.
  • For turbocharged or supercharged engines, use only MLS gaskets with stainless steel fire rings and verify head studs are rated for the boost level (ARP or OEM upgraded).

Specs

Gasket TypeMLS vs Composite
Head Bolt TypeTTY vs Reusable Studs
Compressed Thickness0.5-1.5 mm OEM
Bore OversizeStd, +0.5 mm, +1.0 mm

Related searches

What to check before buying

  • Verify engine code and displacement (e.g., 1.4L LUJ, 3.6L LFX, 5.0L AJ133) before ordering—gaskets are not interchangeable across generations.
  • Confirm block and head material (aluminum vs cast iron) and whether OEM specifies MLS or composite; aluminum requires MLS.
  • Check head bolt type and quantity: TTY bolts are single-use; studs require specific torque sequences and thread sealant.
  • Measure cylinder head and block deck flatness and surface finish (Ra 1.5-2.5 µm for MLS) before installation; machining is required if out of spec.

FAQ

All Engine, Exhaust & Fuel System Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.