Facet Electric Fuel Pump Buying Guide
A Facet electric fuel pump is a solid-state, low-pressure lift pump used to feed carbureted engines, diesel lift circuits, and auxiliary fuel systems. The primary trade-off is between the cube-style interrupter pumps (low flow, low pressure, points ignition) and the cylindrical solid-state pumps (higher flow and pressure, no points to burn). The decision rule: match the pump's pressure and flow rating to your fuel system's demand—anything over 6 PSI needs a bypass regulator, and any gasoline pump must be mounted near the tank, below the fuel level, with a 74-micron pre-filter.
At a glance
- Price range
- Price range not synced yet
- Category
- Engine, Exhaust & Fuel System Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Facet pumps split into two architectures: cube-style (interrupter/points, 2-4 PSI, 15-30 GPH) and cylindrical solid-state (no points, 4-8 PSI, 30-45 GPH).
- Solid-state cylindrical pumps eliminate the mechanical points that wear out in cube pumps, making them the durable choice for daily drivers and high-vibration installations.
- All gasoline-compatible Facet pumps use 1/8-27 NPTF ports and require a 74-micron pre-filter; diesel-compatible models use different seals and must be specified separately.
- Pressure output is factory-set and non-adjustable—choose the PSI rating for your carburetor (typically 2-4 PSI for Weber/SU, 4-6 PSI for Holley) rather than adding a regulator.
Best use cases
- Best fit: carbureted classic car with a mechanical pump failure—pick a 2-4 PSI cube or solid-state pump with 15-30 GPH and mount it below tank level near the rear axle.
- Best fit: diesel lift pump for a generator or tractor—choose a diesel-rated cylindrical pump with 4-6 PSI and 30+ GPH, and install a water-separating pre-filter.
- Wrong fit: fuel-injected engines requiring 40+ PSI—Facet pumps are low-pressure only; use an in-tank EFI pump instead.
- Wrong fit: high-horsepower carbureted race engine above 500 HP—step up to a dedicated high-flow pump (e.g., Holley or Aeromotive) rather than stacking two Facet pumps.
Buying tips
- Match flow to horsepower: gasoline needs roughly 0.5 GPH per HP; a 200 HP engine requires at least 100 GPH system flow, so two 45 GPH Facet pumps or a larger pump are needed.
- Match pressure to fuel system: 2-4 PSI for Weber, SU, and Stromberg carburetors; 4-6 PSI for Holley and Edelbrock; never exceed 6 PSI without a bypass regulator.
- Choose solid-state cylindrical over cube-style for any vehicle driven regularly—the points in cube pumps fail from vibration and are not serviceable.
- Confirm port thread: 1/8-27 NPTF is standard on Facet pumps; use fuel-rated thread sealant, not Teflon tape, to avoid debris in the fuel system.
Specs
| Pump Type | Cube interrupter vs cylindrical solid-state |
|---|---|
| Pressure Range | 2-8 PSI (non-adjustable) |
| Flow Rate | 15-45 GPH (gasoline) |
| Port Thread | 1/8-27 NPTF |
Related searches
What to check before buying
- Measure fuel tank depth and mounting location: Facet pumps are pushers and must sit within 12 inches of the tank bottom, below the fuel level, and protected from road debris.
- Verify electrical system: Facet pumps draw 1-2 amps at 12V; confirm your charging system and wiring can supply a switched 12V feed with a 5-amp fuse.
- Check fuel line size: 5/16-inch or 3/8-inch lines are typical; pump ports are 1/8 NPT, so use appropriate barb or AN adapters rated for fuel.
- Confirm climate and fuel compatibility: ethanol-blended gasoline (E10) is fine with modern Facet pumps, but methanol requires a dedicated methanol-compatible pump.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
