Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

350 Chevy Engine Buying Guide

The 350 Chevy is a 5.7L small-block V8 produced in Gen I (1955-2002) and Gen III/IV LS forms, with the classic Gen I being the dominant crate/replacement engine. Buyers face a core trade-off between cheap rebuilt long-blocks with unknown machine work and new crate engines with documented clearances and warranties. The decisive rule: demand a build sheet or dyno sheet; no documentation means you are buying a core, not an engine.

Displacement:350 cu in / 5.7L V8Main Caps:2-bolt (to ~400 hp) vs 4-boltIntake Pattern:12-bolt pre-1987 / 72-deg 1987+Rear Main Seal:2-piece pre-1986 / 1-piece 1986+
Typical price range$104.99 – $234.99

At a glance

Category
Engine, Exhaust & Fuel System Parts
Data updated
Nov 15, 2026

Current offers

Highlights

  • Gen I 350 uses a 4.000 in bore x 3.480 in stroke with 2-bolt or 4-bolt mains; 4-bolt mains (common in truck and HP blocks) are mandatory above ~450 hp.
  • Factory iron heads (e.g., 882, 993) flow ~180-200 cfm intake and cap output near 300 hp; aftermarket 180-200cc aluminum heads unlock 400+ hp on pump gas.
  • Gen I intake bolt pattern is 12-bolt (1955-86) or 72-degree center-bolt (1987+); mixing them requires matching heads and intake, not adapter shims.
  • LS-series 5.3L/6.0L swaps are not 350s: they use a different bellhousing pattern, relocation-style mounts, and 58x/24x crank triggers for EFI.

Best use cases

  • Best fit: 1967-1986 GM truck or muscle car restoration — pick a Gen I 350 with 4-bolt mains, Vortec-style or aftermarket heads, and a carbureted or TBI-compatible intake.
  • Best fit: 1987-1995 TBI truck — choose a 350 with the 72-degree center-bolt intake pattern and a roller cam-ready block if adding EFI later.
  • Wrong fit: Late-model LS-swap chassis expecting coil-on-plug EFI — a Gen I 350 needs a distributor, different mounts, and a standalone or carb setup; skip it and buy a 5.3L/6.0L LS.
  • Wrong fit: 1996+ Vortec truck — the 350 is a direct fit only with the correct 1996-2000 intake and 4L60E/4L80E flexplate; earlier engines need the matching flexplate and intake.

Buying tips

  • Confirm main cap count: 2-bolt is fine to ~400 hp; 4-bolt (or splayed caps) is required for 450+ hp or forced induction.
  • Match the intake bolt pattern: 12-bolt for pre-1987 heads, 72-degree center-bolt for 1987+ and Vortec heads — the wrong intake will not seal.
  • Check rear main seal type: Gen I 350 uses a 2-piece rear main seal (pre-1986) or 1-piece (1986+); the crank and block must match for flexplate and seal fit.
  • Verify head casting and chamber size: 76cc iron heads yield ~8.5:1; 64cc heads yield ~9.5-10:1 — choose compression for your fuel octane, not the seller's claim.

Specs

Displacement350 cu in / 5.7L V8
Main Caps2-bolt (to ~400 hp) vs 4-bolt
Intake Pattern12-bolt pre-1987 / 72-deg 1987+
Rear Main Seal2-piece pre-1986 / 1-piece 1986+

Related searches

What to check before buying

  • Measure your engine bay and transmission tunnel: a long-block with headers and accessories needs clearance for 1-3/4 in primary tubes and a 2.5-3 in collector.
  • Confirm transmission and flexplate: TH350/700R4 need a 153-tooth or 168-tooth flexplate matching the starter; LS bellhousing patterns will not bolt to a Gen I block.
  • Check your fuel and ignition system: carbureted 350 needs 5-7 psi fuel pressure and a 12V coil feed; EFI swaps need 58 psi and a return line.
  • Verify radiator and cooling: 350s need a 3-core or 2-row aluminum radiator with a 16-18 in mechanical fan or 2,500+ cfm electric fan for street use.

FAQ

All Engine, Exhaust & Fuel System Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.