Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

2013 Ford Fusion Fuel Pump Buying Guide

The 2013 Ford Fusion fuel pump is an in-tank electric assembly that delivers gasoline at pressure to the engine; the key trade-off is OEM-grade turbine/brushless motor and sender durability versus cheaper brushed motors with weaker level sensors. Choose a full assembly with OEM-compatible connectors and a proven turbine design for long-term reliability, and avoid bare pumps or generic brushed units that skip the sender and strainer.

Pump Type:Turbine (OEM-style) vs BrushedAssembly Style:Full module w/ sender vs bare pumpSender Resistance:10-180 ohm (verify gauge match)Fitment Years:2013-2020 Fusion / MKZ (SP2515M)
Typical price range$91.99

At a glance

Category
Engine, Exhaust & Fuel System Parts
Data updated
Nov 15, 2026

Current offers

Highlights

  • Full assembly includes pump, sender unit, strainer, and mounting flange; bare pumps require reusing old sender and seals, risking leaks and inaccurate fuel gauge.
  • Turbine-style pumps run quieter and last longer than older brushed roller-vane designs; OEM Ford units typically use turbine technology for 2013 Fusion.
  • SP2515M cross-reference fits 2013-2020 Fusion and Lincoln MKZ; verify connector pin count and tank seal style before install.
  • Fuel sender resistance must match the factory gauge (typically 10-180 ohm range); mismatched senders cause false empty/full readings.

Best use cases

  • Best fit: full assembly replacement for a 2013 Fusion with crank-no-start or lean codes — pick a kit with new tank seal and strainer to avoid comebacks.
  • Wrong fit: buying a bare pump only for a high-mileage car — the original sender and strainer are usually worn; replace the complete module instead.
  • Best fit: 2013 Fusion with 2.5L or 1.6L EcoBoost — confirm engine-specific flow rate and connector; skip assemblies listed only for 2.0L if your VIN differs.
  • Wrong fit: using a generic universal inline pump to replace the in-tank unit — it will not fit the tank module and will lack the sender signal.

Buying tips

  • Match the assembly cross-reference to SP2515M or Ford OEM part number; 2013 Fusion pumps are not interchangeable with 2012 or 2014+ without checking connector and tank seal.
  • Select a turbine-style pump over brushed for quieter operation and longer life; brushed pumps are acceptable only for low-budget, short-term repairs.
  • Confirm the fuel sender ohm range matches your cluster (commonly 10-180 ohm); wrong range causes gauge errors even if the pump runs.
  • Replace the fuel filter and tank seal at the same time; a clogged filter strains the new pump and voids most warranties.

Specs

Pump TypeTurbine (OEM-style) vs Brushed
Assembly StyleFull module w/ sender vs bare pump
Sender Resistance10-180 ohm (verify gauge match)
Fitment Years2013-2020 Fusion / MKZ (SP2515M)

Related searches

What to check before buying

  • Verify your 2013 Fusion engine (2.5L, 1.6L, or 2.0L EcoBoost) and VIN; pump flow and connector differ by engine.
  • Measure fuel tank size (16.5 gallons for most 2013 Fusion) and confirm assembly fits without modification.
  • Check fuel line fitting type (quick-connect vs threaded) and electrical connector pin count before ordering.
  • Ensure you have a new tank lock ring and seal; reuse of old O-rings causes evaporation codes and leaks.

FAQ

All Engine, Exhaust & Fuel System Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.