Photos from current listings. Actual item, color, and included accessories may vary.
2001 Honda Civic Catalytic Converter Buying Guide
The 2001 Honda Civic catalytic converter is a CARB-compliant emissions component that bolts directly to the exhaust manifold on DX/LX/CX/HX 1.7L models, with California vs. Federal emissions being the critical split. The primary trade-off is OEM-style ceramic honeycomb with heat shield versus universal weld-in units that lack OBD-II sensor bungs and proper backpressure tuning. Buy a direct-fit, emissions-code-matched unit with factory sensor locations; skip universal fitments and any part that does not state CARB or EPA compliance for your specific trim.
At a glance
- Category
- Engine, Exhaust & Fuel System Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- 2001 Civic DX/LX/CX/HX with 1.7L engine uses a manifold-integrated converter (part numbers 18160-PLM-A50/A00) rather than a downstream underbody unit.
- California-emissions (CARB) 2001 Civics require a CARB-certified converter with an executive order number; Federal (EPA) 49-state cars accept EPA-compliant units.
- OEM-style units use a ceramic honeycomb substrate in a stamped stainless housing with an integrated heat shield and two O2 sensor bungs (pre- and post-cat).
- Universal weld-in converters lack factory flanges and sensor placement, causing OBD-II P0420 codes and failed visual inspections on 2001 Civics.
Best use cases
- Best fit: Direct-fit manifold converter (18160-PLM-A50) for a stock 2001 DX/LX/CX/HX 1.7L in a 49-state EPA region — bolt-on, no fabrication, correct sensor bungs.
- Best fit: CARB-certified direct-fit unit for California-registered 2001 Civics — required to pass smog; confirm the executive order number matches the 1.7L engine family.
- Wrong fit: Universal 2-inch weld-in converter on a 2001 Civic — requires cutting and welding, mispositions O2 sensors, and triggers P0420; skip it.
- Wrong fit: Converters listed for 2001-2005 Civic 1.7L that do not specify DX/LX/CX/HX vs. EX — the EX uses a different 1.7L VTEC layout and will not bolt up.
Buying tips
- Match the emissions label under the hood: 'California' or 'CARB' requires a CARB-certified converter with an EO number; 'Federal' or '49-state' accepts EPA-compliant units.
- Confirm the part number 18160-PLM-A50 or 18160-PLM-A00 for 2001 DX/LX/CX/HX 1.7L — these are manifold-integrated units, not underbody converters.
- Check for two O2 sensor bungs (pre-cat and post-cat) and a welded heat shield; missing bungs cause P0420 and heat-soak damage to nearby wiring.
- Stainless-steel housings (409 or 304 grade) outlast aluminized steel in salt-belt climates; ceramic honeycomb is standard, metallic substrate is more durable but rarer.
Specs
| Converter Type | Manifold-integrated direct-fit |
|---|---|
| Emissions Standard | CARB (California) vs EPA (49-state) |
| Engine Fitment | 1.7L SOHC DX/LX/CX/HX (not EX) |
| O2 Sensor Bungs | 2 (pre-cat and post-cat) |
Related searches
What to check before buying
- Verify your 2001 Civic trim: DX, LX, CX, or HX (1.7L SOHC) uses the manifold converter; EX (1.7L VTEC) uses a different exhaust layout.
- Read the emissions decal on the underside of the hood or in the engine bay to confirm California (CARB) vs. Federal (EPA) requirements.
- Inspect the existing manifold-to-downpipe flange and O2 sensor connector types — 2001 Civics use specific 4-wire heated sensors that must plug in directly.
- Confirm you have new gaskets, flange nuts, and heat-shield bolts on hand; reuse of original hardware frequently causes exhaust leaks and rattles.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.

