Small Vented Propane Heater Buying Guide
A small vented propane heater is a sealed-combustion or direct-vent appliance that draws combustion air from outside and exhausts flue gases outdoors, eliminating indoor moisture and CO risk. The core trade-off is between B-vent atmospheric units (cheaper, need vertical rise and 12V-free operation) and power-vented or sealed-combustion models (higher cost, need 12V DC and wall-thimble clearance). The decision rule: buy only a unit rated for RV/mobile use with a dedicated outside-air intake and a factory vent kit, and skip any unvented catalytic or blue-flame heater for sleeping areas.
At a glance
- Price range
- Price range not synced yet
- Category
- RV Ventilation & Heating
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Sealed-combustion direct-vent heaters use a coaxial or two-pipe wall thimble so intake and exhaust pass through one 6-8 in. wall cutout, avoiding backdraft in tight campers.
- B-vent atmospheric models depend on a 12 in. minimum vertical rise and 1/4 in. per ft slope; they work without 12V power but are sensitive to downdraft and altitude.
- Power-vented units draw 1.5-3 A at 12V DC for the combustion blower, so pair with a 100 Ah+ battery bank or 30 A converter to avoid low-voltage shutdown.
- BTU sizing follows ~1,000-1,200 BTU per 10 sq ft of insulated camper floor; a 10,000-12,000 BTU unit suits a 100 sq ft class B van, while 16,000-20,000 BTU fits a 150-200 sq ft travel trailer.
Best use cases
- Best fit: a four-season camper with a pre-cut 2-3 in. wall for a direct-vent thimble and 12V house power — pick a sealed-combustion power-vented unit at 10,000-16,000 BTU.
- Best fit: a vintage trailer or off-grid cabin with no 12V system — pick a B-vent atmospheric heater with a vertical flue and a CO alarm as backup.
- Wrong fit: a pop-up or canvas-sided camper — skip vented propane entirely; soft walls cannot support a thimble and clearance-to-combustibles is unmeetable.
- Wrong fit: a sleeping-area-only install where the buyer wants silent, no-power heat — skip unvented catalytic and choose a sealed direct-vent model with an external combustion air kit.
Buying tips
- Match BTU to floor area using 1,000-1,200 BTU per 10 sq ft, then derate 20% for uninsulated or single-pane campers to avoid short-cycling.
- Require a manufacturer vent kit with a wall thimble rated for the exact wall thickness; universal thimbles rarely meet 1 in. clearance to combustibles.
- For power-vented models confirm a 12V DC blower draw under 3 A and a low-voltage cutoff above 10.5V so the heater shuts down cleanly rather than sooting.
- Choose stainless or aluminized steel heat exchangers over painted mild steel; condensate from propane flue gas corrodes uncoated steel within a few seasons.
Specs
| Vent Type | Direct-vent sealed / B-vent atmospheric |
|---|---|
| BTU Output | 10,000-20,000 BTU for small campers |
| Power Draw | 0 A B-vent / 1.5-3 A 12V DC power-vented |
| Wall Thimble | 6-8 in. cutout, 1 in. clearance |
Related searches
What to check before buying
- Measure the exterior wall for a 6-8 in. thimble and confirm 1 in. clearance to studs, wiring, and foam insulation before ordering.
- Confirm the camper has a 12V DC circuit capable of 3-5 A continuous if choosing a power-vented model; B-vent units need no DC power.
- Verify the propane supply: a 20 lb cylinder with a two-stage regulator and a 3/8 in. flare line sized for the heater's BTU input.
- Install a CO and propane alarm inside the camper regardless of vent type, and check that the vent terminates at least 12 in. above snow line and away from windows.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
