Electric Hot Water Heater Buying Guide
Electric hot water heaters for RVs and campers replace or supplement a propane tank with a 120V AC element, trading propane dependency for shore-power or generator draw. The core decision is heating architecture (tank vs tankless) and element wattage against your available AC amperage, not brand marketing. Buy a tanked 6-gallon 120V unit for simple drop-in replacement; choose tankless only if you have reliable 30A+ shore power and low simultaneous hot-water demand.
At a glance
- Price range
- Price range not synced yet
- Category
- RV Ventilation & Heating
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Tanked RV units are typically 6 or 10 gallons with a 1,400–1,500W 120V element drawing 12–13A, a direct swap for most propane-only heater cutouts.
- Tankless electric models need 3,000–5,500W at 120V or 240V, drawing 25–45A and often requiring a dedicated breaker and upgraded shore-power pedestal.
- Tank recovery takes 30–60 minutes for 6 gallons; tankless delivers endless flow only when inlet water is above roughly 50°F and amperage is sufficient.
- Stainless-steel tanks and glass-lined steel resist RV water chemistry better than aluminum; anode-rod service life is the main durability variable.
Best use cases
- Best fit: full-hookup campgrounds with 30A service — pick a 6-gallon 120V tanked unit for reliable showers and dishwashing without generator noise.
- Best fit: boondocking or generator-limited rigs — keep propane as primary and add a 1,400W electric element only for surplus-solar or generator hours.
- Wrong fit: 15A household-style pedestal — a 3,000W+ tankless unit will trip breakers; stay with a 1,400W tanked heater or propane.
- Wrong fit: cold-climate winter camping — tankless electric struggles with 40°F inlet water; use a tanked unit with freeze protection or propane.
Buying tips
- Match element wattage to pedestal amperage: 1,400–1,500W on 15–20A circuits, 3,000–3,500W on 30A, 4,500–5,500W on 50A; never exceed 80% of breaker rating.
- Measure the existing heater cutout and plumbing centers before ordering; standard RV tanked heaters use 6-gallon footprints with 3/4-inch NPT or PEX fittings.
- Choose a tank material grade: stainless steel or glass-lined steel for long-term mineral resistance; aluminum tanks are lighter but corrode faster in hard water.
- For tankless, confirm minimum activation flow (typically 0.5–1.0 GPM) and temperature rise at your winter inlet temp; undersized units short-cycle.
Specs
| Heater Type | Tanked 6–10 gal vs Tankless |
|---|---|
| Element Wattage | 1,400–5,500W (120V/240V) |
| Circuit Draw | 12–45A at full heat |
| Tank Material | Stainless / Glass-lined / Aluminum |
Related searches
What to check before buying
- Measure the old heater enclosure width, height, and depth plus door clearance; tanked replacements are not one-size-fits-all.
- Confirm shore-power pedestal amperage (15A/30A/50A) and breaker size at the heater circuit before choosing element wattage.
- Check plumbing fitting type and location — 3/4-inch NPT, PEX crimp, or quick-connect — and whether a mixing valve or bypass kit is required.
- Verify freeze protection: tank drain, anode rod access, and whether the unit sits inside conditioned space or an exposed bay.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
