Rv Heating Buying Guide
RV heating is the category of built-in and portable systems that keep a coach livable in cold weather, spanning propane furnaces, electric space heaters, hydronic systems, and heat-pump/AC combos. The core trade-off is BTU output and fuel source versus power draw, venting safety, and installation footprint. Choose a sealed-combustion propane furnace for whole-coach ducted heat below freezing; choose electric or heat-pump heat only when you have adequate shore power and above-freezing ambient temperatures.
At a glance
- Price range
- Price range not synced yet
- Category
- RV Ventilation & Heating
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Propane RV furnaces are rated in BTU/hr input and output; typical Class B/C units run 12,000-40,000 BTU/hr and use 12V DC blower power plus 4-inch ducting.
- Sealed-combustion furnaces draw outside air for the burner and exhaust combustion gases outdoors, eliminating interior oxygen depletion and CO risk.
- Electric space heaters convert 1,500W to about 5,100 BTU/hr and require a dedicated 15A/20A shore circuit; heat-pump rooftop units deliver 2-3x that heat per watt above roughly 40°F.
- Hydronic diesel or propane systems circulate heated glycol to fan coils and domestic hot water, delivering quiet, even heat without large duct runs.
Best use cases
- Best fit: Four-season or sub-freezing camping — install a sealed-combustion propane furnace sized to coach volume with ducted distribution and a wall thermostat.
- Best fit: Mild-weather and full-hookup campgrounds — a 1,500W ceramic or oil-filled electric heater on a dedicated 20A circuit heats a Class B efficiently without propane.
- Best fit: Boondocking without propane access — a diesel-fired hydronic or air heater tied to the coach fuel tank avoids separate fuel bottles.
- Wrong fit: Running a catalytic or unvented propane heater in a sealed RV — skip it; moisture, CO, and oxygen depletion make sealed-combustion or electric the only safe choices.
Buying tips
- Size the furnace at roughly 10-15 BTU/hr per cubic foot of coach volume for typical insulation, then add 20-30% for single-pane windows or extreme cold.
- Match the furnace flue and intake to the coach wall thickness and exterior clearances; standard RV furnace vent kits specify wall cutout depth and minimum clearance to combustibles.
- Confirm the furnace blower and controls run on 12V DC and that the coach converter/charger can supply the 3-7A blower draw during dry camping.
- For electric heat, verify the shore power inlet and breaker: a 1,500W heater draws 12.5A at 120V, so do not share a 15A circuit with a microwave or coffee maker.
Specs
| Heat Source | Propane furnace / electric / hydronic |
|---|---|
| BTU Output | 12,000-40,000 BTU/hr typical |
| Combustion Type | Sealed-combustion vented vs unvented |
| Electrical Draw | 12V DC 3-7A blower / 120V 12.5A heater |
Related searches
What to check before buying
- Measure the furnace closet or under-bed cavity against the unit's cutout dimensions and confirm duct runs can reach front and rear zones.
- Check exterior wall thickness and vent termination clearance to windows, doors, and fuel fillers per the furnace installation manual.
- Verify the coach has a working LP leak detector, CO alarm, and propane regulator sized for the furnace plus water heater and stove loads.
- For electric heaters, confirm the pedestal breaker rating and use a dedicated 12-gauge extension cord no longer than 25 feet.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
