Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Honda Pilot Control Arm Buying Guide

Honda Pilot control arms are the forged or stamped steel links that locate the front suspension and carry the lower ball joint, and the key trade-off is between OEM-style stamped assemblies with serviceable pressed ball joints and budget complete-arm kits that pair softer rubber bushings with non-replaceable joints. Durable options use thicker gauge steel, sealed ball joints, and bonded rubber bushings rated for the vehicle's curb weight; compromises thin the stamping, skip corrosion coating, and ship unloaded bushings that fail early.

Arm Construction:Stamped steel / forged steelBall Joint Type:Sealed non-greasable / greasableBushing Material:Bonded rubber / polyurethaneFitment Generation:2003-2008 vs 2009-2015 Pilot
Typical price range$189.99 – $398.99

At a glance

Category
Suspension, Steering & Brake Parts
Data updated
Nov 15, 2026

Current offers

Highlights

  • First-generation Pilot (2003-2008) and Acura MDX share lower control arms and ball joints, but second-generation Pilot (2009-2015) uses different geometry and separate part numbers — arms are not interchangeable across generations.
  • Lower control arms carry the load-bearing ball joint and the compliance bushing; upper arms on the Pilot are short stamped links with bushings only, so most wear and replacement cost sits in the lower arm assembly.
  • OEM-style replacement arms use stamped steel with pressed-in ball joints and bonded rubber bushings; complete loaded-arm kits include the ball joint and hardware but often use lower-grade rubber that cracks sooner in salt-belt climates.
  • Torque-to-yield fasteners and alignment cam bolts are single-use on the Pilot — reuse of original cam bolts or omitted alignment after installation causes premature bushing wear and uneven tire wear.

Best use cases

  • Best fit: daily-driven 2009-2015 Pilot with a clunking front end and torn compliance bushings — buy a loaded lower control arm with a sealed ball joint and new cam bolts rather than pressing bushings into a worn arm.
  • Best fit: 2006-2008 Pilot or first-gen MDX doing a full front refresh — a 10-piece kit covering lower arms, tie rods, and sway links is the correct tier when multiple joints are worn at once.
  • Wrong fit: a single right-front lower arm on a high-mileage Pilot where the left side and ball joints are original — replacing one corner accelerates wear on the opposite side; replace in pairs.
  • Wrong fit: off-road or lifted Pilot builds using stock-length control arms — extended travel requires high-angle ball joints and corrected camber, which standard replacement arms do not provide.

Buying tips

  • Match the generation exactly: 2003-2008 Pilot and first-gen MDX arms share part families, while 2009-2015 Pilot arms (K621550/K621551 lower) do not fit earlier cars — verify by year and model, not by 'Pilot' alone.
  • Choose arms with sealed, non-greasable ball joints and bonded rubber bushings for street use; greasable joints add a maintenance interval most owners skip, leading to water ingress and rust.
  • Buy loaded arms (ball joint and bushings pre-installed) when the original arm has over 100,000 miles — pressing new bushings into a fatigued stamping rarely restores factory geometry.
  • Replace both sides and include new alignment cam bolts and nuts; reusing torque-to-yield hardware or skipping a four-wheel alignment after install is the leading cause of repeat control-arm complaints.

Specs

Arm ConstructionStamped steel / forged steel
Ball Joint TypeSealed non-greasable / greasable
Bushing MaterialBonded rubber / polyurethane
Fitment Generation2003-2008 vs 2009-2015 Pilot

Related searches

What to check before buying

  • Confirm the exact model year and trim — 2009-2015 Pilot arms differ from 2003-2008 and from Acura MDX part numbers; cross-check the stamped number on the original arm.
  • Inspect the subframe and cam bolt mounts for elongation or rust-through before buying arms; worn mounting holes will loosen new bushings regardless of arm quality.
  • Verify ball-joint stud taper and thread size match your steering knuckle — mixed-year knuckle swaps are common on used Pilots and cause joint pull-out.
  • Check lug-nut torque and wheel-bearing play during the same job; a worn bearing mimics control-arm noise and will mask a successful repair.

FAQ

All Suspension, Steering & Brake Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.