Car Gear Picks

Ford Explorer Strut Buying Guide

A Ford Explorer strut is a coil-over MacPherson assembly (or bare strut insert) that carries spring load, damps rebound/compression, and sets front ride height on 1991–present Explorers. The core trade-off is gas-charged twin-tube (OEM ride, lower cost) versus monotube (firmer, heat-resistant, longer service life) and complete quick-strut versus bare strut requiring spring/seat/mount transfer. Buy the complete assembly with new mount, bearing, and boot for 80k+ mile vehicles; choose bare struts only when the coil spring, upper mount, and bearing are verified within spec.

Strut Type:Twin-tube gas / MonotubeAssembly Format:Complete quick-strut / Bare strutGeneration Fit:1991–2001 / 2002–2010 / 2011–2019 / 2020+Mount Included:Yes (complete) / No (bare)

At a glance

Price range
Price range not synced yet
Category
Suspension, Steering & Brake Parts
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • Twin-tube gas struts match factory valving for 1991–2010 and 2011–2019 Explorers; monotube conversions stiffen compression and resist fade under load.
  • Complete quick-struts include coil spring, upper mount, bearing, and dust boot; bare struts require a spring compressor and reuse of original springs and mounts.
  • Front strut mount bearings and rubber upper mounts wear by 100k miles; reusing them on new struts causes clunking and memory steer.
  • 2011+ Explorer front struts are longer and heavier than 1991–2010 units; 2020+ Explorer (U625) uses a different top mount and spring rate and does not interchange.

Best use cases

  • Daily-driven 2002–2010 Explorer with leaking front struts: buy complete quick-strut assemblies with new mounts and bearings for both sides, not bare inserts.
  • 2011–2019 Explorer with worn rear coil springs: buy rear complete strut-and-spring assemblies; do not reuse original rear springs on new bare shocks.
  • Lifted or heavy-load 1991–2001 Explorer: choose monotube or heavy-duty valved struts and pair with corrected-length springs; skip OEM-replacement twin-tubes.
  • Low-mileage 2020+ Explorer with a single damaged strut: replace in pairs with the correct U625-generation assembly; do not install 2011–2019 struts.

Buying tips

  • Match strut generation to year: 1991–2001, 2002–2010, 2011–2019, and 2020+ each use different spring rates, mount plates, and strut lengths.
  • Replace front or rear struts in pairs on the same axle; mismatched damping causes uneven tire wear and unpredictable handling.
  • For vehicles over 80k miles, buy complete quick-struts that include upper mount, bearing, boot, and bump stop rather than transferring worn parts.
  • Verify spring rate and load rating when towing or hauling: standard Explorer springs sag under tongue weight; choose heavy-duty or towing-spec assemblies.

Specs

Strut TypeTwin-tube gas / Monotube
Assembly FormatComplete quick-strut / Bare strut
Generation Fit1991–2001 / 2002–2010 / 2011–2019 / 2020+
Mount IncludedYes (complete) / No (bare)

Related searches

What to check before buying

  • Confirm exact model year and trim (base, XLT, Limited, Sport, ST) because spring rates and strut valving differ across trims.
  • Measure current fender-to-ground height on both sides to detect sagging springs before ordering bare struts versus complete assemblies.
  • Inspect upper strut mount and bearing for cracks or looseness; replace them with the strut if reusing springs.
  • Check wheel and tire clearance if the Explorer is lifted or running oversized tires; strut length and spring perch height must match.

FAQ

All Suspension, Steering & Brake Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.