Car Gear Picks

2013 Ford Explorer Strut Buying Guide

A 2013 Ford Explorer strut is a structural suspension assembly that combines a coil spring, gas-charged damper, and upper mount into one bolt-in unit for the front or rear corners of the vehicle. The primary trade-off is between OEM-style twin-tube replacements that preserve ride comfort and heavy-duty monotube or quick-strut assemblies that add durability at the cost of a firmer ride. The decision rule: match the strut to the axle, drivetrain, and ride-control option your Explorer was built with—base, XLT, Limited, or Sport—because spring rates and valving differ across trims and a mismatch degrades handling and tire wear.

Strut Design:McPherson front / coil-over rearAssembly Type:Quick-strut vs bare strutDrivetrain Fit:FWD vs AWD specificTrim Tuning:Base/XLT/Limited vs Sport/Police

At a glance

Price range
Price range not synced yet
Category
Suspension, Steering & Brake Parts
Data updated
Nov 15, 2026

Current offers

No verified match right now. Browse live listings:

Highlights

  • 2013 Explorer front struts are McPherson-style complete assemblies; rear suspension uses independent multilink with coil-over shocks, so front and rear parts are not interchangeable.
  • Ford built the 2013 Explorer in FWD and AWD configurations with distinct spring and damper tuning; AWD units carry different part numbers due to weight and load distribution.
  • Police Interceptor Utility versions of the 2013 Explorer use heavy-duty struts and springs rated for pursuit duty; these fit civilian models but deliver a noticeably stiffer ride.
  • Quick-strut assemblies include the coil spring, upper mount, and bearing pre-assembled; bare struts require spring compression with a wall-mounted or clamshell compressor rated for the spring's wire diameter.

Best use cases

  • Best fit: daily-driven 2013 Explorer XLT or Limited with worn original dampers past 80,000 miles—choose OEM-replacement twin-tube quick-struts for factory ride height and comfort; skip monotube or lifted assemblies.
  • Best fit: 2013 Explorer Sport or Police Interceptor Utility used for towing or heavy loads—pick heavy-duty monotube or pursuit-spec struts rated for higher spring rates; skip base-model twin-tube units that will fade under load.
  • Wrong fit: buyers wanting a lift or leveling kit—2013 Explorer struts are not lift struts; a spacer lift requires separate geometry correction and alignment, so do not buy oversized struts expecting lift.
  • Best fit: high-mileage AWD Explorers with rust-belt exposure—choose coated or painted strut bodies and replace the upper mount and bearing at the same time; skip reused mounts that fail prematurely.

Buying tips

  • Match struts to the axle and drivetrain: front struts differ from rear coil-over shocks, and AWD part numbers differ from FWD—verify the vehicle's door-jamb axle code before ordering.
  • Replace struts in pairs per axle; a new strut paired with a worn one causes uneven damping, accelerated tire cupping, and unpredictable emergency-lane-change behavior.
  • For quick-strut assemblies, confirm the included spring rate matches the trim—Sport and Police Interceptor springs are stiffer than base and XLT springs, and mixing them changes ride height and alignment.
  • Inspect the upper strut mount and bearing during replacement; on 2013 Explorers the bearing wears with the strut and a reused mount causes clunking and steering bind within tens of thousands of miles.

Specs

Strut DesignMcPherson front / coil-over rear
Assembly TypeQuick-strut vs bare strut
Drivetrain FitFWD vs AWD specific
Trim TuningBase/XLT/Limited vs Sport/Police

Related searches

What to check before buying

  • Record the vehicle's axle code and trim from the door-jamb sticker and VIN; confirm FWD vs AWD and base/XLT/Limited/Sport/Police Interceptor before selecting a strut tier.
  • Measure current ride height from wheel center to fender arch on level ground; compare against the new strut's stated stock ride height to catch lift or lowering mismatches.
  • Confirm the strut includes or reuses the upper mount, bearing, and dust boot; quick-struts include them, bare struts require separate purchase.
  • Check wheel and tire clearance and plan a professional alignment immediately after installation, since strut replacement alters camber and toe on the 2013 Explorer's multilink rear.

FAQ

All Suspension, Steering & Brake Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.