Photos from current listings. Actual item, color, and included accessories may vary.
2003 Honda Pilot Power Steering Pump Buying Guide
The 2003 Honda Pilot power steering pump is a hydraulic vane pump driven by the serpentine belt, and it is shared across the 2003–2013 Honda Odyssey, Acura MDX, and Pilot with the 3.5L/3.7L V6. The main trade-off is between a remanufactured OEM pump with a known housing and a new aftermarket pump with unknown metallurgy; the decision rule is to buy a new pump only if it includes a pulley and specifies the J35A4 fitment, otherwise choose a remanufactured Honda core.
At a glance
- Category
- Suspension, Steering & Brake Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- The 2003 Pilot uses the J35A4 3.5L V6 and the pump is a belt-driven vane pump operating at roughly 1,200–1,500 psi; the pulley must match the 6-rib serpentine belt.
- OEM Honda pumps use a cast aluminum housing and a steel pressure plate; aftermarket replacements often use a stamped steel housing that can warp and leak at the outlet fitting.
- Remanufactured pumps reuse the original Honda housing and are bench-tested to 1,500 psi; new aftermarket pumps are typically built to a lower pressure tolerance and may whine at cold start.
- Cross-compatibility spans 2003–2013 Odyssey, MDX, and Pilot with 3.5L/3.7L engines, but the 2003 Pilot requires the specific 21-5442 casting number or equivalent Honda part number 56110-RCA-A01.
Best use cases
- Best fit: daily-driven 2003 Pilot with a leaking original pump and no pulley damage — choose a remanufactured OEM pump with a new O-ring and crush washer.
- Best fit: off-road or high-mileage Pilot where the pump whines and the pulley is worn — choose a new aftermarket pump that includes a pulley and mounting bracket.
- Wrong fit: 2003 Pilot with a failing rack-and-pinion or contaminated fluid — do not replace only the pump; flush the system and replace the reservoir or the new pump will fail within months.
- Wrong fit: 2003 Pilot with a 2WD vs 4WD difference — the pump is the same, but the belt routing differs; do not buy a pump without confirming the pulley groove count matches your engine.
Buying tips
- Confirm the pump casting number: 21-5442 is the common aftermarket cross-reference for the 2003–2013 3.5L/3.7L, and it must match your original pump's casting or the mounting bolt holes will not align.
- Require a new pulley and a new pressure hose O-ring in the box; reusing the old pulley on a new pump often causes belt misalignment and premature bearing failure.
- Choose a pump with a cast aluminum housing over a stamped steel housing; cast aluminum resists heat cycling and holds the outlet fitting thread better.
- Verify the pump includes a reservoir cap and a new serpentine belt if the old belt is glazed; a glazed belt will slip on a new pump pulley and cause whine.
Specs
| Pump Type | Belt-driven hydraulic vane |
|---|---|
| Engine Fitment | 3.5L/3.7L V6 (J35A4) |
| Pulley Grooves | 6-rib serpentine |
| Housing Material | Cast aluminum (OEM) vs steel |
Related searches
What to check before buying
- Measure the serpentine belt width and rib count: the 2003 Pilot uses a 6-rib belt, and the pump pulley must have 6 matching grooves.
- Check the power steering fluid type: the 2003 Pilot requires Honda Genuine Power Steering Fluid or a compatible ATF-Z1; using Dexron will degrade the pump seals.
- Inspect the mounting bracket bolt holes on the engine block: the 2003 Pilot has three mounting bolts, and the pump flange must match the 3-bolt pattern.
- Confirm the pressure hose fitting size: the 2003 Pilot uses a 16mm banjo fitting at the pump outlet; a mismatched fitting will leak under pressure.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.


