Photos from current listings. Actual item, color, and included accessories may vary.
2003 Honda Accord Power Steering Pump Buying Guide
A 2003 Honda Accord power steering pump is a hydraulic vane pump driven by the serpentine belt, and the primary trade-off is OEM-grade metallurgy and seal quality versus remanufactured or budget aftermarket units that may leak or whine within months. The decision rule is simple: match the pump to the exact engine (2.4L L4 vs 3.0L V6) and buy a unit with a new (not reused) housing and a verified pulley shaft seal, skipping any listing that does not state the Honda part number cross-reference.
At a glance
- Category
- Suspension, Steering & Brake Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- 2003 Accord split by engine: 2.4L L4 uses pump 56110-RAA-A01 (21-5341), while 3.0L V6 uses a different pump and bracket — these are not interchangeable.
- The L4 pump is a belt-driven vane pump with an integral reservoir; a failing unit typically whines at cold start, leaks from the shaft seal, or sends metal debris into the rack.
- Remanufactured pumps reuse the original aluminum housing and bore; new aftermarket pumps use fresh castings but vary widely in seal and bearing grade.
- The 21-5341 interchange covers 2003–2005 Accord L4 only; 2006–2007 facelift cars and V6 models require different part numbers despite similar engine bays.
Best use cases
- Best fit: a 2003 Accord LX/DX/EX with the 2.4L four-cylinder and a confirmed 56110-RAA-A01 stamp — buy the 21-5341 pump and a new o-ring kit.
- Wrong fit: a 2003 Accord V6 (3.0L) owner — skip all L4 pumps and source the V6-specific pump and mounting bracket.
- Best fit: a high-mileage car with a whining pump and dark fluid — replace the pump plus flush the rack and lines, or debris will destroy the new unit.
- Wrong fit: a car with a cracked reservoir or leaking high-pressure hose only — skip the pump and replace the failed line or reservoir first.
Buying tips
- Verify the engine first: 2.4L L4 cars take 56110-RAA-A01 / 21-5341; 3.0L V6 cars take a different pump — confirm by VIN or engine cover before ordering.
- Choose a pump with a new housing and shaft seal, not a reman that reuses the original aluminum bore; remans are acceptable only with a fresh seal kit and bearing.
- Match the pulley: the L4 pump uses a specific serpentine pulley; a mismatched pulley will squeal or shred the belt within miles.
- Replace the o-ring, high-pressure hose crush washers, and reservoir cap at the same time — reused seals are the top cause of repeat leaks.
Specs
| Engine Fit | 2.4L L4 only (2003-2005) |
|---|---|
| Honda Part No. | 56110-RAA-A01 |
| Interchange No. | 21-5341 |
| Pump Type | Belt-driven vane, integral reservoir |
Related searches
What to check before buying
- Confirm the engine displacement (2.4L L4 vs 3.0L V6) and the Honda part number stamped on the original pump before ordering.
- Check the belt routing and pulley diameter match your car's serpentine belt — a different pulley will not align.
- Inspect the high-pressure hose and rack boots for leaks; a failed hose will mimic pump failure after replacement.
- Have Honda Genuine power steering fluid (or equivalent) on hand — do not use generic ATF in this system.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.


