Rv Electric Hot Water Heater Buying Guide
An RV electric hot water heater replaces or supplements the tank or tankless water heater in a recreational vehicle using 120V AC shore power or 12V DC battery power. The core trade-off is between fast recovery via dual electric elements and high amp draw that can trip a 30A pedestal breaker, versus lower-wattage heating that is slow but pedestal-safe. The decision rule: match element wattage to your RV's electrical service (30A vs 50A) and choose a tank material that resists the corrosive water found in campgrounds.
At a glance
- Price range
- Price range not synced yet
- Category
- RV Water & Plumbing
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Element wattage tiers: 1500W draws ~12.5A at 120V, while 2000W draws ~16.7A; dual 1500W elements require a dedicated 20A breaker and cannot run simultaneously on a 30A pedestal.
- Tank material hierarchy: stainless steel (316L or 304) resists chloride pitting far better than aluminum or glass-lined steel; porcelain-lined steel is the minimum for hard water.
- Tankless electric models need a minimum 1.5 GPM flow switch and 3000W+ to deliver hot water at the tap; tank-style 6-gallon units with 1500W recover in about 30-45 minutes.
- Electric-only units lack a propane backup, so total reliance on shore power means no hot water during boondocking; dual-fuel (LP + electric) models are the standard for mixed camping.
Best use cases
- Best fit for 30A campground pedestals: a 6-gallon electric-only tank with a single 1500W element; skip 2000W+ or dual-element units that will trip the main breaker when the air conditioner runs.
- Best fit for full-time 50A hookups: a 10-12 gallon dual-element electric tank or a 3000W tankless unit; skip small 4-gallon tanks that cannot keep up with two showers.
- Wrong fit for boondocking or dry camping: any electric-only heater drains the battery bank; choose a propane/electric dual-fuel model or a propane-only tank instead.
- Best fit for retrofitting an existing propane-only tank: an electric conversion kit with a 1500W element and thermostat; skip universal kits that lack a sacrificial anode port.
Buying tips
- Calculate amp draw before buying: divide wattage by 120V. A 30A RV service can safely run one 1500W heater (12.5A) plus a 13.5k BTU AC (~13A), but not two heating elements at once.
- For tankless electric, confirm your incoming water temperature and flow rate: a 3000W unit raises 1.5 GPM by roughly 35°F; cold groundwater below 50°F may need a 5500W unit.
- Choose a tank with a replaceable sacrificial anode rod; in hard or sulfurous water, the anode should be checked every 6 months and replaced when more than 50% consumed.
- Match the heater's pressure relief valve (typically 150 PSI) and plumbing thread (1/2-inch NPT or 3/4-inch NPT) to your RV's existing water lines to avoid adapters.
Specs
| Power Source | 120V AC / 12V DC / Dual-fuel |
|---|---|
| Element Wattage | 1500W / 2000W / 3000W+ |
| Tank Capacity | 4 / 6 / 10 / 12 gal |
| Tank Material | Stainless / Porcelain-lined / Aluminum |
Related searches
What to check before buying
- Measure the installation bay: tank-style 6-gallon units need roughly 16x16x20 inches of clearance; tankless units need wall space and 12 inches of vent-free clearance.
- Confirm your RV's electrical service amperage (30A or 50A) and whether the heater circuit is dedicated; a 50A rig can support dual 1500W elements on separate breakers.
- Check water hardness and chloride content: above 200 ppm chloride, choose stainless steel over aluminum or glass-lined steel to prevent pitting.
- Verify the heater's inlet/outlet fitting size and orientation (side-mount vs top-mount) match your existing plumbing; mismatched fittings require PEX or SharkBite adapters.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
