Car Gear Picks

Photos from current listings. Actual item, color, and included accessories may vary.

Ford F150 Side Mirror Replacement Buying Guide

Ford F-150 side mirrors are a high-wear exterior assembly spanning three distinct generation architectures, each with fixed mounting, wiring, and feature protocols. The core trade-off is between OEM/salvage assemblies with correct connectors and feature modules versus aftermarket units that may omit camera or blind-spot electronics. The decision rule: match the mirror to your truck's exact generation and factory feature set—14th-gen (2021+) mirrors with cameras and BLIS cannot be swapped with 12th- or 13th-gen units without losing driver-assist functions.

Generation Fit:12th 2009-14 / 13th 2015-20 / 14th 2021+Connector Pins:2-4 glass / 8-12 power / 16+ memory+BLISFeature Modules:Camera, BLIS, puddle lamp, power foldMounting Studs:3-stud bracket; 4.5 vs 4.75 in centers
Typical price range$378.99

At a glance

Category
Body, Interior & Hardware Parts
Data updated
Nov 16, 2026

Current offers

Highlights

  • Generation split: 2009-2014 (12th gen) uses simple 2-6 wire connectors; 2015-2020 (13th gen) adds 360-camera and BLIS options; 2021+ (14th gen) integrates camera, BLIS, and puddle lamp in one module.
  • Feature wiring differs by trim—XL/XLT mirrors may be manual glass with no power fold, while Lariat and above use 8-12 pin connectors for power fold, turn signal, and memory.
  • Glass replacement alone requires only a heated-glass pigtail (2 wires); full housing swap needs the correct connector and module programming for camera or BLIS to function.
  • OEM mounting uses three studs on a stamped steel bracket with fixed torque; aftermarket housings with plastic brackets are prone to vibration and mirror shake at speed.

Best use cases

  • Best fit: 2021-2024 F-150 with factory 360-camera and BLIS—buy a mirror with ML3Z-style connector and camera module; skip 2015-2020 units, which use different pinouts and bracket angles.
  • Best fit: 2015-2020 XLT with manual-fold, non-camera mirrors—a basic 6-pin power glass assembly is sufficient; skip higher-trim camera mirrors that add unused wiring and cost.
  • Wrong fit: 2009-2014 truck with a 2021+ mirror—mounting stud spacing and door harness are incompatible; use 12th-gen-specific assemblies only.
  • Best fit: glass-only crack on any generation—replace the glass with a heated pigtail-matched lens; skip full housing swap unless the motor or bracket is damaged.

Buying tips

  • Count the pins in your factory door harness connector before buying: 2-4 pins = manual/power glass only; 8-12 pins = power fold, signal, and camera; 16+ pins = memory and BLIS.
  • Match the mirror's connector keyway to your generation—12th gen (2009-2014) uses a rectangular 6-pin; 13th gen (2015-2020) uses a 10-pin; 14th gen (2021+) uses a 12-pin with camera coax.
  • For BLIS-equipped trucks, the mirror must include the radar module bracket and correct LIN bus wiring; a non-BLIS mirror will trigger a dash warning and disable the system.
  • Heated glass replacements use a 2-wire pigtail with a specific connector; verify the pigtail matches the door harness plug—cutting and splicing voids the heating circuit's water seal.

Specs

Generation Fit12th 2009-14 / 13th 2015-20 / 14th 2021+
Connector Pins2-4 glass / 8-12 power / 16+ memory+BLIS
Feature ModulesCamera, BLIS, puddle lamp, power fold
Mounting Studs3-stud bracket; 4.5 vs 4.75 in centers

Related searches

What to check before buying

  • Measure the three mounting stud spacing on your door bracket—12th gen uses 4.5-inch centers, 13th/14th gen use 4.75-inch centers; a mismatch means the mirror will not bolt on.
  • Confirm your truck's door harness connector pin count and keyway by pulling the inner door panel or checking the mirror's factory plug, not the listing photo.
  • Check voltage and ground at the mirror connector with a multimeter—12V on the glass heater circuit confirms the door harness is live before installing a new assembly.
  • Verify whether your truck has memory seats—memory mirrors use a 16-pin connector with a dedicated position sensor wire that non-memory mirrors lack.

FAQ

All Body, Interior & Hardware Parts buying guides

Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 16, 2026.

Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.