Photos from current listings. Actual item, color, and included accessories may vary.
NISSAN QUEST Buying Guide
The Nissan Quest emergency tire tool kit is the factory jack and lug-wrench assembly stored behind the third-row seat in 2004–2017 Quest minivans, not a universal roadside kit. The main decision is whether to replace a missing factory tool with an OEM-matched scissor jack and tire-iron set or a higher-capacity aftermarket scissor jack rated for the Quest's 3,500–4,000 lb curb weight. Buy the OEM-spec or higher for jacking force and leg reach; skip compact-car emergency kits, which lack the lift height and saddle geometry for a minivan.
At a glance
- Brand
- Not synced yet
- Model
- Not synced yet
- MPN
- Not synced yet
- Category
- Emergency Tire Tools
- Status
- Offers available
- Data updated
- Nov 15, 2026
Current offers
Highlights
- Nissan Quest curb weight spans roughly 3,800–4,200 lbs across 2004–2017 generations, so the jack must be rated well above that — a 2-ton (4,000 lb) minimum, 2.5-ton preferred.
- Factory Quest scissor jacks are body-panel-stored under the third-row seat floor; a stamped steel scissor with roughly 4,000–4,500 lb capacity and 15-inch collapsed height matches the stock well.
- Quest lug nuts are 21mm (13/16-inch) hex on a 5-lug pattern; the factory tire iron is a folding L-wrench, so a 21mm deep six-point socket on a breaker bar is the correct substitute.
- The spare is a temporary T-type donut rated for about 50 mph and short distances; the tool kit's job is to swap it quickly, not to enable a full-size spare conversion.
Best use cases
- Best fit: 2004–2017 Quest owners missing the factory under-floor jack kit — buy an OEM-matched scissor jack, 21mm lug wrench, and hold-down bracket that fit the third-row storage well.
- Best fit: High-mileage Quest used for rideshare or family hauling — upgrade to a 2.5-ton scissor jack with a wider saddle and a telescoping 21mm breaker bar for faster roadside changes.
- Wrong fit: Buying a compact-car emergency kit or 1-ton scissor jack — a 4,000 lb minivan needs more lift force and taller reach than these provide; the jack will strain or fail.
- Wrong fit: Expecting a full-size replacement tire to fit under the Quest floor — the well is sized for the T-donut, so keep a donut-spec spare and match the tool to it.
Buying tips
- Match jack capacity to the Quest's 3,800–4,200 lb curb weight with margin: choose 2-ton (4,000 lb) minimum, 2.5-ton for regular loaded hauling.
- Confirm collapsed height under 6 inches and maximum lift around 15–17 inches, so the jack fits under a flat tire and lifts to the Quest's stock ride height.
- Get a 21mm (13/16-inch) six-point deep socket or forged lug wrench; the Quest's 5-lug nuts are 21mm, and a 12-point or undersized wrench will round them.
- Prefer a forged steel scissor jack with a wide rectangular saddle and a captured crank handle; stamped thin-gauge jacks twist and strip under minivan loads.
Specs
| Jack Type | Scissor jack, forged steel |
|---|---|
| Lift Capacity | 2–2.5 ton (4,000–5,000 lb) |
| Lug Nut Size | 21mm (13/16 in) hex, 5-lug |
| Lift Height Range | ~6 in collapsed / ~15–17 in max |
Alternatives to compare
What to check before buying
- Measure the under-floor storage well behind the third row — the jack, wrench, and bracket must fit flat so the seat and cargo floor close normally.
- Verify your Quest's lug-nut size (21mm on 2004–2017) and lug count (5) before buying a wrench or socket.
- Check the jack saddle height range against your tire's flat height and the Quest's 15–17 inch lift requirement to the jacking point.
- Confirm the jack contacts the Quest's reinforced pinch-weld or frame jack point — a saddle that is too narrow or too tall can slip or dent the rocker panel.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.







