6r140 Transmission Buying Guide
The 6R140 is Ford's heavy-duty six-speed automatic used in 2011-2019 Super Duty trucks and chassis cabs, plus 2011-2019 6.7L Power Stroke applications; it replaced the TorqShift 5R110 and is known for a high-torque 6.7L diesel torque converter and integrated PTO provision. The core buying trade-off is rebuilt vs. remanufactured vs. used: rebuilt units vary widely in solenoid pack, valve body, converter, and clutch quality, while factory remans carry a warranty but cost more. The decision rule: match the transmission's model-year and engine calibration to your truck, buy only from builders who replace the solenoid pack and converter and provide a VIN-matched warranty, and avoid used units with unknown mileage or salvage history.
At a glance
- Price range
- Price range not synced yet
- Category
- Transmission & Drivetrain Parts
- Data updated
- Nov 15, 2026
Current offers
Highlights
- 6R140 gear ratios are 3.97, 2.32, 1.52, 1.00, 0.86, 0.67; the 6.7L diesel version uses a low-stall heavy-duty torque converter tuned differently from 6.2L gas units.
- 2011-2014 and 2015-2019 6R140 units differ in solenoid pack and TEHCM (transmission control module) calibration; mismatched generation causes harsh or no shifts.
- Integrated PTO provision is standard on Super Duty 6R140 cases, allowing stationary or mobile PTO operation without an aftermarket adapter.
- Rebuild quality hinges on replacing the TEHCM/solenoid body, updating the valve body separator plate, and using revised clutch materials; fluid capacity is approximately 13-17 quarts depending on converter and cooler.
Best use cases
- Best fit: direct replacement in a 2011-2019 6.7L Power Stroke Super Duty with matching VIN-year calibration; choose a reman with TEHCM and converter included.
- Best fit: chassis-cab or fleet trucks needing PTO-driven equipment; confirm the replacement case retains the PTO port and correct output shaft for your application.
- Wrong fit: 6.2L gas trucks shopping diesel 6R140 units or vice versa—converter stall and calibration differ and will cause drivability faults.
- Skip: salvage units with unknown mileage for towing or high-load use; without documented rebuild history the clutch and solenoid wear are unverifiable.
Buying tips
- Match by VIN and model year: 2011-2014 vs 2015-2019 6R140 solenoid/TEHCM and calibration differences make them non-interchangeable without module reprogramming.
- Require documentation that the solenoid pack/TEHCM, valve body, torque converter, and clutches were replaced or remanufactured—these are the wear and failure points.
- Confirm output shaft and tail housing configuration (2WD vs 4WD, Super Duty vs chassis cab) before ordering; they are not universal across 6R140 applications.
- Verify fluid spec: 6R140 uses Motorcraft MERCON LV (or equivalent licensed LV fluid); incorrect fluid causes shift quality and clutch durability problems.
Specs
| Transmission Type | 6-speed heavy-duty automatic |
|---|---|
| Engine Fitment | 6.7L Power Stroke / 6.2L gas |
| Gear Ratios | 3.97 / 2.32 / 1.52 / 1.00 / 0.86 / 0.67 |
| Fluid Spec | MERCON LV (approx. 13-17 qt) |
Related searches
What to check before buying
- Read the transmission ID tag and VIN-year calibration to confirm the replacement matches your 2011-2019 6R140 generation and engine.
- Measure and confirm 2WD or 4WD output shaft length and tail housing pattern; chassis-cab units can differ from pickup units.
- Check cooler condition and lines before install—debris from a failed unit contaminates the new transmission without flushing.
- Confirm warranty terms in writing: mileage/time coverage and whether removal/reinstallation labor or fluid is included.
FAQ
Data sources: eBay / Amazon listings and product attribute feeds Data updated Nov 15, 2026.
Some links on this page are affiliate links. If you buy after clicking one, we may earn a commission at no extra cost to you. This does not change which products appear here or their order. Affiliate disclosure.
